Jump to content
SAU Community

Recommended Posts

  • 2 weeks later...

some more progress.

secondary injectors will fit, took abit to get them sitting in the rite spot so they dont spray on to the runner and port walls and without putting the hole in the wrong spot to start with.

post-19586-0-94566200-1453540872_thumb.jpgpost-19586-0-17971500-1453540885_thumb.jpgpost-19586-0-26049500-1453540898_thumb.jpg

post-19586-0-65167000-1453540913_thumb.jpgpost-19586-0-11975000-1453540924_thumb.jpg

swaybar will need some modding

post-19586-0-96543300-1453541023_thumb.jpg

had some action in the backyard withe the next doors tree...

post-19586-0-84173400-1453541099_thumb.jpg

  • Like 1

no speed sensors. not really necessary. atmospheric conditions can change the boost given the same comp speed. i will be running a balance pipe on the back of the engine to average the boost to each bank.

just working out the heater/turbo plumbing atm. + water to air cooler plumbing+ our lease is up and have to move.........

secondary injectors all mounted.

It looks schmick, nice job. But why go to staged injection when you can run injectors up to 2000cc that will idle and run nicely down low as well?

If it's bling, I understand. But the work / complexity increase would make me shy away.

  • 2 weeks later...

It looks schmick, nice job. But why go to staged injection when you can run injectors up to 2000cc that will idle and run nicely down low as well?

If it's bling, I understand. But the work / complexity increase would make me shy away.

because i want it to pass an im240 if need be. my ecu can run it, and with proper injector placement i wont need as big. better economy and more consistent mixtures.

ive got a set of moran billet atomisers that will do the job, but i want it done well. fyi the "2000 ish cc" injectors on the market are gas injectors and fail on a regular basis. there not meant for liquid petrol. let alone e85. the rubber seals inside swell and change there dynamic flow rate.

yes some updates. having our lease up sucks. house hunting has taken a front seat over this.

also i am abandoning the water to air intercoolers in the manifolds. the volume is to big and will make it lazy. (i need razor sharp throttle response for the paddle shift that im running.

also bonnet clearance is an issue. i want to raise the engine a cm or 2 for ground clearance. stock sump will be marginal at best,,

ive got some old hypertune s2000 plenum shells i am modding to fit. (shortening and mirror imaging one for the r/h bank)

the water to air coolers will be mounted in the inner guards out of the way.

all but finished my 110L fuel tank. all in 316L so it wont corrode. twin walbro 400's staged and an internal gated surge tank/pot

post-19586-0-09213900-1457252365_thumb.jpgpost-19586-0-20692500-1457252375_thumb.jpgpost-19586-0-53988000-1457252389_thumb.jpg

  • Like 1
  • 2 months later...
  • 6 months later...
  • 1 month later...

getting close. just finding the time has been hard + the 90 odd wires for the engine wiring harness took some time to make.

got the air shift piston and linkage sorted so i can use the stick and have paddle shift.

                                                                                                               DSC_0292.JPG

DSC_0317.JPG

shouldn't get hot with the "super fan"                                                                                                                                                     

DSC_0318.JPGDSC_0293.JPG

 

  • Like 6

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I thought Australia got rid of the "drag dodgy fuel up to 91 RON with ethanol", which is why all E10 advertise as "up to 94 RON" ? Anyway I put E10/91 in the missus' Mazda because she empties the tank weekly, when all my cars get 98RON. tl;dr - turbo - 98 RON, if you can't afford that, sell it and get a commuter car (or tune your car for 91, which no one does).
    • Yeah i found that alot of parts can be wrong or "very" hard to get the real right one. I already bought some brakes years ago on me "old" GT calipers and they were wrong too 😄  I told them too. Even send them pictures...but they said "EBC catalogue has them on my car... So i dont know what their answer will be. I call monday them and let them know that they are really not on my car. If they were they would be already on a car...
    • Welcome to Skyline ownership. Yes, it is entirely possible parts websites get things wrong. There's a whole world of inaccuracies out there when it comes to R34 stuff (and probably 33 and 32). Lots of things that are 'just bolt on, entirely interchangable' aren't. Even between S1 and S2 R34's. Yes they have a GTT item supposedly being 296mm. This is incorrect. I would call whoever you got them from and return them and let them know the GTT actually uses 310mm rotors. Depending on where you got them from your experience and success will obviously vary.
    • Hi...a bit a "development" on the brakes. I spoke to the guys where i get brakes from...and they are saying that 296mm EBC are for R34 GT-T. I then went to their site: https://www.ebcbrakes.com/vehicle/uk-row/NISSAN/Skyline (R34)/ and search for my car(R34 GT 1998 - it has GTT brakes) and it show me this USR1229 number and they are rly 296mm rotors... So now iam rly confused... The rotors i have now on the car are 310mm asi shown... So where is the problem? Does the whole EBC got it wrong or my calipers are just...idk know what?  
    • Oh What the hell, I used to get a "are you sure you want to reply, this thread is XX months old" message. Maybe a software update remove that. My bad.
×
×
  • Create New...