Jump to content
SAU Community

Recommended Posts

Unfortunately the new custom sump was modelled on an R33 and it didn't clear the swaybar enough when we put it in last week.

Because of this we missed out at PI on the weekend. I had brand new rubber on the thing and was ready to go but no such luck...

Turns out that the whiteline sway bar that is on my car was a prototype from years ago and they don't sell them anymore so pretty unique situation. The bend is very close to the sump so that's what has caused the issue. I think that a new 27mm sway bar with a better option that pulling the sump off again! Custom one being investigated now. Hope it makes the 21st!!

  • 2 weeks later...

time for another update...

New 27mm swaybar has just arrived to solve the sump clearance issues. I currently have a loan 24mm until I get a chance to fit the 27mm. Might try both on the weekend if I can as a comparison.

Fulcrum suspension have sorted out the bar for me.

I've extended the wing end plates as the old ones were a little small and the bigger ones should hopefully stop a bit of the spill over the sides.

post-10715-0-12315400-1342526396_thumb.jpg

The splitter has come a long way. I'm still testing as it's all a bit new to me still. I'm really just copying what the fast guys do and following basic principles and advice I'm getting along the way.

I'll be logging the data at Philip Island this weekend to see if straight line speed is sacrificed and if corner speed is increased. As a bare minimum I'm expecting more downforce from just the splitter seperating the air and minimising air flow under the car.

If it all works the plan is to make the parts out of carbon fibre down the track. It's all trial and error at the moment.

post-10715-0-15594600-1342526630_thumb.jpg

post-10715-0-67829500-1342526762_thumb.jpg

post-10715-0-83309300-1342526985_thumb.jpg

loving the alloy canards. i made some about 3 years ago and was laughed at. been hesitant to make any new ones.

i seen in a build thread for an american R35 time attack car they made canards out of alloy. they were far easier and cheaper and did the same job.

are the uprights for your wing an off the shelf item?

Yeah the ally is pretty light except for the splitter. It's damn heavy. CF would be so much better

are the uprights for your wing an off the shelf item?

Nah they were made by superleggera carbon fibre in sydney. They're pretty hard core!

Yeah the ally is pretty light except for the splitter. It's damn heavy. CF would be so much better

Nah they were made by superleggera carbon fibre in sydney. They're pretty hard core!

oh they look like a production type thing.

do you have any bracing under the boot lid? i may have missed it.

Hope you don't mind Russ. Most people probably know what happened already!

Russmans R32 GTST blasting around PI in it's last shakedown before WTAC!

For the full article check out Autocult -> CLICK HERE!

7629603330_b9209c015b_b.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
×
×
  • Create New...