Jump to content
SAU Community

Recommended Posts

Try to keep to those days too Troy...it's important to have the Wednesday off. You don't have to do it on those exact days of the week, but as long as you have that day off in the middle of the split...then the split will work very well and shouldn't leave you too wrecked. Ease into it too, as like Nick said, 4 day splits can be very fatiguing. More important than weight when starting off, is that you get the technique for each exercise downpat - this will also help with easing your body into it. Other than that, I've seen good results from beginners and advanced following that program, provided they stick to it and give it a decent chance. Built up a couple of people using it - some got very good results from it, to the point of people complimenting their physique...then dropped out of the gym?

Built up a couple of people using it - some got very good results from it, to the point of people complimenting their physique...then dropped out of the gym?

hard to maintain a 4 day a week gym routine... unless your a real gym/fitness junkie... I'm sure its more effective with faster results than 3 or even 2 sessions a week but I see this stuff as long term, and personally I know I wouldn't be able to keep it up... also if you play a sport or have other engagements outside work it can make things difficult

if you have the dedication and motivation I say go for it, but its not going to work for everyone

now if I can hurry up renovating my place, clear out the spare room of all the painting supplies/tools and finally setup the gym I've been wanting... then I can see myself getting in 4 sessions a week... sometimes its not the workout I don't want to do, I just can't be arsed dealing with a gym full of people

plus at home I can stare lovingly at myself in the mirror... lol

Tis hard to maintain 4 days a week if you're not addicted or if you haven't seen worthy results from it.

I'm very curious to see this famous birds 4 day routine. Could you please pm it to me birds? Wouldn't mind comparing it to what I'm doing and maybe get a few ideas out of it. Cheers mate

Sure mate, will PM to you. There's nothing amazing about it, it's just what I've ended up with after more than a few years at the gymnasium and changing things around until I struck a good balance - a comprehensive routine with good strength and aesthetic gain, not leaving yourself too fatigued / overtraining, and fitting it all inside a 7 day week.

plus at home I can stare lovingly at my wife... lol

FYP, I hope!

Too hard to keep track of what program people are talking about...would be good to have a section, then people can criticise or modify a program within it's own thread. But yeah, I might make a thread and put mine up.

Monday Flat Bench 10 x 10 - 5 km walk

Tuesday Body Weight Heaves or Pull Downs 10 x 10

Wendsday Squats 10 x 10 - 5 km walk

Thursday Shoulder Press 10 x 10

Friday Dead Lift 10 x 10 - 5 km walk

Sat 5 km walk with max push ups and max sit ups every 1 km.

Sunday Sleep

Use enough weight so the last set only gets 6-8 reps, when you can do all 10 x 10 go up 2.5 - 5kg

You do not need to do curls or tri ext or any other pretty boy exercises, you need power exersises to make your whole body strong so when someone attacks you you can 1 take the hit, then, 2 pick them up and break them on the ground.

This is what I used when I first started training, 1985, I ate alot of heathy foods 6 times a day and the only supps I took was a Multi Vit, Protien drinks consisted of skim milk powder and chocolate syryp, drink lots of water and skim milk, always carry a water bottle with you, tupperware is your friend, pack food.

Dont eat sh it, you are what you eat, if you eat fat burgers you will be fat burgers, but dont be so stict that your bored with your food, protien protien protien, any food that has alot of protien is good, as well as food with iron, dont eat to many carbs, after training is OK for some carbs but not always, listen to your body, it will tell you what you need, if you feel tired have some more carbs

Sleep a minimum of 8 hrs a night and nap if you can, every hour past midnight your awake add 1 more hour to the 8.

I went from 65 kg to about 80 kg in 6 months, and lots of strength.

30 yrs on though, Im 85kg but not so much muscle, more so fat, LOL.

only 4 days a week?

That including cardio? or just weights sessions?

It's just weight sessions. My cardio is usually done around that on days away from the gym, or sometimes straight afterwards.

Try to keep to those days too Troy...it's important to have the Wednesday off. You don't have to do it on those exact days of the week, but as long as you have that day off in the middle of the split...then the split will work very well and shouldn't leave you too wrecked. Ease into it too, as like Nick said, 4 day splits can be very fatiguing. More important than weight when starting off, is that you get the technique for each exercise downpat - this will also help with easing your body into it. Other than that, I've seen good results from beginners and advanced following that program, provided they stick to it and give it a decent chance. Built up a couple of people using it - some got very good results from it, to the point of people complimenting their physique...then dropped out of the gym?

Yep, I'm very much about proper technique.

hard to maintain a 4 day a week gym routine... unless your a real gym/fitness junkie... I'm sure its more effective with faster results than 3 or even 2 sessions a week but I see this stuff as long term, and personally I know I wouldn't be able to keep it up... also if you play a sport or have other engagements outside work it can make things difficult

if you have the dedication and motivation I say go for it, but its not going to work for everyone

now if I can hurry up renovating my place, clear out the spare room of all the painting supplies/tools and finally setup the gym I've been wanting... then I can see myself getting in 4 sessions a week... sometimes its not the workout I don't want to do, I just can't be arsed dealing with a gym full of people

plus at home I can stare lovingly at myself in the mirror... lol

I couldn't agree with you more, that's the problem with mine - SO MANY PEOPLE

4 afternoons a week will be fine almost every week for me. If I'm going to be strapped for time one arvo, I'll just go knock off half that day's exercises during lunch - I work about 5 minute walk from the gym, and live only 5 minute drive away.

ALSO!!!! Just returned from my 6.5 weeks overseas in Europe. Weighed myself and discovered I've in fact LOST about 1.5kg. I can guarantee I've put on a bit of fat, so I'm a bit sad that I must have dropped quite a bit of muscle :( on the other hand, it at least tells me I had plenty of muscle to lose in the first place, lol. Now just gotta get it all back.

72kg now, aiming for 80kg by summer with preferably the same BF% as before my trip, or less :D

It's just weight sessions. My cardio is usually done around that on days away from the gym, or sometimes straight afterwards.

Oh good, cause i was going to say thats not enough.. i do 7-8 gym weight sessions a week, sport and training twice a week for my cardio. I never know whether i want to bulk up or get shredded haha

That sounds a bit excessive for the weight sessions? Unless you're training only one group of muscles each session? My weight sessions are made up of two different days, i.e. predominantly push and predominantly pull, which are repeated twice a week for a total of 4 sessions per week. Each session takes about 60-75 minutes to complete and is fairly comprehensive. I don't believe in leaving a whole week between training a group of muscles, for a day or two is plenty of time to recover. In fact, when I've had to miss a push day and a pull days, it has been that much harder to get through the workout the next time I do it. This really creates a good amount of endurance without fatiguing the body too much or overtraining.

Everyone says that, but it works for me. One muscle group per session, twice a week. Has been working for me for 3 years now so im sticking to it.

Its hard to get big and keep lean without roids etc lol so it takes alot of hard work, which is what i do.

Yep 3 days is all the recovery one muscle/group needs.. I remember doing chest about 2 weeks ago, flat bench dumbells. I did chest 3 days earlier, it was still sore... Car got defected so i had alot of built up anger, did 50kg dumbells 13reps 2 sets. And i was sore before hand haha.. always push to new levels or you will get no where/bored.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I did end up getting it sorted, as GTSBoy said, there was a corroded connection and wire that needed to be replaced. I ended up taking out the light assembly, giving everything a good clean and re-soldered the old joints, and it came out good.
    • Wow, thanks for your help guys 🙏. I really appreciate it. Thanks @Rezz, if i fail finding any new or used, full or partial set of original Stage carpets i will come back to you for sure 😉 Explenation is right there, i just missed it 🤦‍♂️. Thanks for pointing out. @soviet_merlin in the meantime, I received a reply from nengun, and i quote: "Thanks for your message and interest in Nengun. KG4900 is for the full set of floor mats, while KG4911 is only the Driver's Floor Mat. FR, RH means Front Right Hand Side. All the Full Set options are now discontinued. However, the Driver's Floor Mat options are still available according to the latest information available to us. We do not know what the differences would be, but if you only want the one mat, we can certainly see what we can find out for you". Interesting. It seems they still have some "new old stock" that Duncan mentioned 🤔. I wonder if they can provide any photos......And i also just realized that amayama have G4900 sets. I'm tempted too. 
    • Any update on this one? did you manage to get it fixed?    i'm having the same issue with my r34 and i believe its to do with the smart entry (keyless) control module but cant be sure without forking out to get a replacement  
    • So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if something was binding the shaft from rotating properly. I got absolutely no voltage reading out of the sensor no matter how fast I turned the shaft. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
    • So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if shttps://imgur.com/6TQCG3xomething was binding the shaft from rotating properly. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
×
×
  • Create New...