Jump to content
SAU Community

Recommended Posts

6 x Xspurt 1000's and Proflow RB25 rail would be around $800 through me I think Mark, with all adapters.

Scotty - will that rail fit with the stock plenum? We are looking at going to E85 in the next few months, so I am interested in an injector upgrade.

I think so mate, the 1000's might be a tight fit, but the shorty 750's and 2000's are definitely no issue. I may even be able to get 1000's in the same shorter 1/2 length.

The SR20 rail kit I sell comes with a plenum spacer to help the 1000's clear the upper plenum. Perhaps you could do a similar thing to the RB plenum halves using bakelite or a similar insulating material, that way you would stop the heat transfer into the upper plenum also.

What paper filter are you using, I was told to be careful when use paper filter cause the ethanol can/does eat away the "glue" that holds the filter element to the casing

I'm using a speed flow 10 micron stainless sceen filter but the paper ones can go down to 5-6 micron which would be better

I am using twin Proflow stainless mesh filters, I haven't cleaned them in 3-4 years, since they were installed. I can't remember what micron they were...

The paper filters I have been buying were SX brand, suitable for alcohol fuels. (They have a similar 8an housing to the proflow/Speedflow style filters, and might just drop in to them.) I run the SX fuel reg in my car without issues so I knew it was good gear.

A little Googling reveals Arram as a Japanese manufacturer who make injectors, throttle bodies and carburetors.

Yeah, just wasn't much info and didn't know if these were common in rb20's or not.

Most of the stuff says 550cc, so should be all good, cheers. ;)

Hopefully it doesn't cost you too much dyno time to set them up, it can take a while to work out suitable lag times etc with unusual injectors, and you are paying good coin for every minute it's on the dyno.

Unless you have the lag time report with them? Might be worth trying to source one.

Hopefully it doesn't cost you too much dyno time to set them up, it can take a while to work out suitable lag times etc with unusual injectors, and you are paying good coin for every minute it's on the dyno.

Unless you have the lag time report with them? Might be worth trying to source one.

Never knew injectors even came with a "Lag time report" lol..

I was going to get them tested and flowed before I chucked them on anyway. I think they're a little old.. :P

  • 3 weeks later...
  • 4 years later...

To save starting a new thread.....

Is the contents of this thread still relevant?!?!

As in are the ID injectors still worth paying basically twice the price or are the EV1-Bosch items closer to the mark 5 years down the track?

(Looking for 11mm units to suit standard RB26 fuel rail to get me around the 400rwkw mark on E85...)

ID1300x or 1250cc.....?!?

 

 

Edited by mr_rbman

There are better options (than ID specifically) and have been for years.  You should perhaps PM Scotty to find out what he can do for you.

Basically, if you can get unmolested EV14 injectors in the size you need, that is best approach.  But even the ones that have been decapped are pretty good.

5 minutes ago, GTSBoy said:

There are better options (than ID specifically) and have been for years.  You should perhaps PM Scotty to find out what he can do for you.

Basically, if you can get unmolested EV14 injectors in the size you need, that is best approach.  But even the ones that have been decapped are pretty good.

I had tried pming Scotty before posting but either his inbox is full or there's an SAU issue as i just get an error saying he can't receive messages, or something similar....

Cheers for the reply though....

I do have the 1250cc injectors that Kudos sell in my 'cart' but after reading a few threads on here and then googling I was having second thoughts....

Tier 1 - ID 

Tier 2 (½ the price) - Bosch Motorsport

Tier 3 (aka shit and not worth it, also ¼ the price) - Everything else

Genuine Bosch Motorsport '040' injectors with adapters for RB26 manifold would be the go. I'm sure NZEFI sell them as a kit.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...