Jump to content
SAU Community

Recommended Posts

Its going to be hard to find a direct stock replacement.

You are better off picking up some larger denso/sard injectors off ebay (which are low imp) and buy a nistune board for his ecu.

I picked up some Sard 550cc GTR injectors for like $500. Throw in another $200 for the nistune board. $700 all up and opened the door for future tuning :)

His got a power fc at the moment but not yet installed. I told him to fit some ID1000/Bosch injectors as he will be looking for big power down the track.

Money is the issue at the moment, but I say do it once do it right.

His got a power fc at the moment but not yet installed. I told him to fit some ID1000/Bosch injectors as he will be looking for big power down the track.

Money is the issue at the moment, but I say do it once do it right.

Sell the PowerFC and use it to pay for injectors + nistune.

Sell the PowerFC and use it to pay for injectors + nistune.

You guys should chat, his name is Justin from the beach cruise and AGM if you remember.

How come you went the Sard's and not the ID/Bosch injectors as they are only about $100 per injector?

His got a power fc at the moment but not yet installed. I told him to fit some ID1000/Bosch injectors as he will be looking for big power down the track.

Money is the issue at the moment, but I say do it once do it right.

You say it wrong bruvva... gotta say: do it phaggot.

You guys should chat, his name is Justin from the beach cruise and AGM if you remember.

How come you went the Sard's and not the ID/Bosch injectors as they are only about $100 per injector?

ah yeah i remember. With the clean r32 GTR.

SARD's were the cheapest on ebay at the time, reputable brand and it was a direct replacement for GTR. (i had gtr stock injectors wired in which failed, so easier to replace with sard gtr's)

It's also good to replace the injector plugs as they will no doubt be coroded/rusted. Mine were green, no idea how any voltage went through it...

I failed E*P*A because the inspector told me my injectors should be red and not purple, so whatever he gets make sure to paint them to stock colour. However, he wont pass EPA with a powerfc whereas with a nistune and tuned to pass emissions will ;)

Used to dominate zombie horde! 200-3 and shit...

Mad fun playing the zombies, humans didn't stand a chance against zombie me, people actually stopped playing on the server :D

ah yeah i remember. With the clean r32 GTR.

SARD's were the cheapest on ebay at the time, reputable brand and it was a direct replacement for GTR. (i had gtr stock injectors wired in which failed, so easier to replace with sard gtr's)

It's also good to replace the injector plugs as they will no doubt be coroded/rusted. Mine were green, no idea how any voltage went through it...

I failed E*P*A because the inspector told me my injectors should be red and not purple, so whatever he gets make sure to paint them to stock colour. However, he wont pass EPA with a powerfc whereas with a nistune and tuned to pass emissions will ;)

I'll pass it on to him :thumbsup:

I was going to get 550's in and hop around with that for a while untill I get the power fc in and tuned. Now im just thinking I'll get the 750's slap em in got new pod filters waiting to go in, get a adjustable FPR and I'll put my power fc in and change oils untill I can get it booked in for a tune and most likely strap it to the back or a trailer and tow it down.i dears??

Me and a coworker just smashed Nandos $21 full chicken, seriously large chips and 1.5L coke meal for 7th consecutive day.

I think I'm gonna start sweating hot & bbq sauce.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...