Jump to content
SAU Community

Recommended Posts

Yeh me and birds bought a box each, dont know why, any more than one is pretty hard to eat..

And Matt, that sucks! But I wanted to avoid it with the 200 hence selling the shit. Now it's a bucket of shit so I win

Height + Exhaust. Teins at FULL HEIGHT, not lowered one bit and he said the height checker hit on the mid muffler which is a load of shit. Exhaust he didn't even hear once.

Absolutely crooked cop.

I got done for the mid muffler too. Now I'm in Honda town

Mate at work keeps telling me to watch Suits....what's it about? Comedy?

Might get the first ep or 2 and see what I think of it....Need something to watch while waiting for breaking bad and sons to come back on, and something to break up the eps of gangland would be good.

Saw Django tonight, very good movie. DiCaprio was brilliant.

in the anus.... within 12 hours of that post i would assume

More or less the same place as that. Out front of Knox, he was in the BP there pulling someone over. I went past and he jumped in his car and rocketed out of there and came after me. I still like that he did me for too low after I raised the car even more, well above legal height. Absolute cockhead was fuming he couldn't get me for anything so made up some bullshit forcing me to get a rwc. Minor defect and I get a fine + have to get a rwc.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
    • I hope that is not something that bad. From what i remember he said that only first gear is "hard" to get in and that he has couple of ideas what to try next but idk 😕  hope it is not gearbox out. I will let you know.
    • If it's not the hydraulics, it is probably gearbox back out. Usually as per @Duncan's post, or otherwise associated with not getting the throwout fork positioned correctly. All the way up to catastrophically bolting shit back together without it being aligned properly and wrecking the clutch/input shaft/flywheel/something else.
×
×
  • Create New...