Jump to content
SAU Community

Recommended Posts

are verbal contracts not legal in vic?

retty sure he entered into one with you. i would not have f**king paid mate. i would have told them to change it back and pay them nothing.

Try proving it though, or spending $35 to take them to VCAT over $20. If they have invoices showing that they normally charge that for the service, you're fresh out of luck. They also have the right to hold your vehicle until payment is made.

Sucks, but yeah. Always have to get written quotes these days...even on cheap shit lol

Try proving it though, or spending $35 to take them to VCAT over $20. If they have invoices showing that they normally charge that for the service, you're fresh out of luck. They also have the right to hold your vehicle until payment is made.

but. but. but.

im scarey. that usually works. :wacko:

My local place fkd me last time I went in there...

I asked how much it would cost for them to flip my two rear tyre on the rim... Since they had some camber wear and I wanted to use the remaining outer tread for deca... I was told we can do that for $22... I asked "For both the rear tyres?" "Yep we'll do them both". so I was thinking "Finally a place that isn't going to rip me off".

I go down the street, have some lunch, come back and suddenly it's $44... $22 each... fuuuuuu, classic bait and switch. Said that was bullshit, and he dropped it to "$40, is the lowest we can do"

*rage*

that's why, i always pay, before the job is done.

or get a written quote if they refuse to let me pay. =P

Scary can work. I'd probably give you your $18 back...but not Simon...he's a cuddly koala.

nawww thanks babe.

simon. grow more beard/wear more leather. amazing how much shit gets done easier for you.

WL Brahs, anyone know of someone considering selling their 32 GTR? Must be rebuilt engine (preferably forged goodies and shiet). Neighbour interstate locations like NSW/SA is alright, too!

One of my mates is on the hunt for dat dere skyrice.

put a stock evo 9 MR BOV on the car instead of the atmo one that it came with to try and stop the car attempting to stall every time you come to a stop.

its so super sleeperish now, 90db exhaust + nearly inaudible BOV, the loudest thing when you rev it is the pod filter.

Try proving it though, or spending $35 to take them to VCAT over $20. If they have invoices showing that they normally charge that for the service, you're fresh out of luck. They also have the right to hold your vehicle until payment is made.

Sucks, but yeah. Always have to get written quotes these days...even on cheap shit lol

no need to prove shit.... i take my car... i am big

even if you are small it's pretty easy to kick up enough of a fuss to lose them another $40 customer

just came back from Lezzet on Brighton rd (contemporary The land of goat sphincter rings). was really really tasty. Wanted everything on the main course menu, got to taste 4 of them and all were good. Efse Dark Pilsener went down well with roasted pumpkin seeds.

Edit: not allowing the county the sphincter of the universe to be typed on a forum is rascist

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...