Jump to content
SAU Community

Recommended Posts

#@r34abz mate, as long as you don't have an inter-cooler with that pod, it's fine. As Alvin said, one intake mod is ok and if you've got everything stock you'll pass. EPA's are the reason I don't want to get an aftermarket exhaust.

  • Like 1

Check out this Mitsubishi Lancer.

http://www.carsales.com.au/private/details/Mitsubishi-Lancer-2001/SSE-AD-2839584

Nick is this yours?

Nope, mine sold on fleabay not long ago for $12k, un-regod, no rwc, recent engine swap, shit condition car overall and still had the jdm-007 plates

bit steep, are they forged? I got brand new TE37's for a little bit more than that...

I have no idea what my stud pattern is, what widths/offsets I'd need etc.. haven't looked into anything yet

pcd is 5x120 so same as bmw

however not sure on offset, would need to pull a front and rear to check if stamped on inside, if not need to measure and calculate

measure the exact width of th rim, from outer edge to outer edge (may have to lay it down and go with a tape from a flat surface from bottom to top as it's got tyres)

then measure from wheel hub to the lip on the rear

take the first measurement (lip to lip) and divide into 2

then take second measurement (hub to lip) and minus the first measurement from that

Meisters are rad. Sort it out Leroy Jenkins

LEROYYYY JENNNNKIIIIINNNNNNSSSSSSSSSSSSSSSSSSSSSSSS

bit steep, are they forged? I got brand new TE37's for a little bit more than that...

I have no idea what my stud pattern is, what widths/offsets I'd need etc.. haven't looked into anything yet

Not forged, good luck finding good forged rims in these type of sizes for anywhere near this sort of money though ;)

Sure, if you ran pulsar sizes you could buy TE37s cheap.

:D

Green shell killshot just before the finish line is the finest play in the Mario kart book

there is a decidedly real satisfaction from sniping with green shells

but i was foreveralone playing with computer

Nope, mine sold on fleabay not long ago for $12k, un-regod, no rwc, recent engine swap, shit condition car overall and still had the jdm-007 plates

pcd is 5x120 so same as bmw

however not sure on offset, would need to pull a front and rear to check if stamped on inside, if not need to measure and calculate

measure the exact width of th rim, from outer edge to outer edge (may have to lay it down and go with a tape from a flat surface from bottom to top as it's got tyres)

then measure from wheel hub to the lip on the rear

take the first measurement (lip to lip) and divide into 2

then take second measurement (hub to lip) and minus the first measurement from that

LEROYYYY JENNNNKIIIIINNNNNNSSSSSSSSSSSSSSSSSSSSSSSS

Way too much effort. I'm sure it's on the internet..

Pretty sure it's just 2010+ models with power to weight of < 130 kW/t

Anything older will continue to be banned as per current rules / power to weight

I think you may be able to get a Golf R now. Saw some talk of this. Definitely the GTi I think?

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
    • When you pulled it off, there is no signs of blown head gasket? Is it possible you have some other issues going on? Possible cracked blocked? Or do you think it's straight up lifting the head? Did you check what the head was torqued to before pulling it down (To see if possibly they're stretching, or starting to break threads out etc)?
    • Seems like a decent result for a modded JZX110. They are bulky in comparison to the 100 and 90 models (which I'd prefer myself) but they are getting very few and far between here in JP these days. Thanks for the detailed review and the import process into the UK. I also have a car which I'm hoping to export from Japan at some stage so it's good to know if someone from the UK was interested in it. By the way the corrosion underneath is par for the course for cars which were located in/near the mountains or along the Japan sea coastline. They get huge amounts of snow every winter and the sodium chloride is used on the roads. Many cars have some kind of rubber like treatment underneath but they tend to limit it to the wheel arches underbody and fuel tank. Suspension arms and sub-frames will have similar corrosion to your JZX110 which is a common sight. See it all the time and car dealers here generally don't even mention it unless asked.
    • If the sound goes away when you clutch in, the 1.5/2 way diffs are just shit, and you are a normal person. The diff is likely "fine" but driving at anything under 30kmh is a violent horrible experience. It would be exaggerated with solid diff bushings and subframe bushings if you have those.
×
×
  • Create New...