Jump to content
SAU Community

Recommended Posts

Aint even cheap.

First Kakimoto R cost me $80, HKS Super drager was $120 incl courier from qld, Fujitsubo Legalis Super Ti was $250

African American please. this is me. id offer him 50 bucks.

  • Like 1

Aint even cheap.

First Kakimoto R cost me $80, HKS Super drager was $120 incl courier from qld, Fujitsubo Legalis Super Ti was $250

I should go to the exhaust place at the end of the street and ask him how much it'd cost for him to custom make me something with the same specs as the Fujitsubo Legalis Super Ti.

Surely it'd only be $250 since it'll have no big name branding or anything...

I should go to the exhaust place at the end of the street and ask him how much it'd cost for him to custom make me something with the same specs as the Fujitsubo Legalis Super Ti.

Surely it'd only be $250 since it'll have no big name branding or anything...

then ad 0 on end cos hes strayan.

:O

You dream about Skylines instead of Pulsar?

yeah... maybe cause i could thrash it and not care/break anything (important)

lucky skyline owners have aftermarket exhausts around every corner... most other people have to hunt 2nd hand stuff down or get custom.

yeah... maybe cause i could thrash it and not care/break anything (important)

lucky skyline owners have aftermarket exhausts around every corner... most other people have to hunt 2nd hand stuff down or get custom.

go cry on a pulsar forum nancy boy

Also want to be taken for a spin :D

On another note, after going from shagged 275 NT05s to 245 Dunlops I've gone from traction in 2nd on good roads to 'lols' but I don't feel like I'm going to spin out to a tree in the wet which is nice.

Edited by UNR33L

Did you end up fixing your sexcel after breaking at Alvins? What turned out to be problem? May have asked before lol

yeah, clutch slave cylinder stuffed up along with gearbox.

It's running like a little rocket pocket now.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...