Jump to content
SAU Community

Recommended Posts

Both can make you money just differently.

Capital growth gives you a big payout (minus capital gains tax) if the property shoots up in value.

Whereas high rental yield will pay off the mortgage repayment allowing you to borrow against it for another property etc. if the rentals are paying themselves off, eventually you'll have a steady stream of rental income trickling through as profit.

Yeah the second one sounds more like what I want... Can't see the value of the properties going up that dramatically any time soon.

What's the go with the 5 year stuff, buying a house withn 5 years old etc, for claiming depreciation or whatever...if you buy a 4 year old house, does that mean you only get a year of whatever that claim is...

Or you buy an old property, Reno it with your tradie contacts & either flip it or rent. If you flip it you will have to pay 40% tax on the profit else just rent it for a larger sum which puts it close to the mortgage repayment.

Yeah the second one sounds more like what I want... Can't see the value of the properties going up that dramatically any time soon.

What's the go with the 5 year stuff, buying a house withn 5 years old etc, for claiming depreciation or whatever...if you buy a 4 year old house, does that mean you only get a year of whatever that claim is...

No idea in that space. Only have experience with old properties.

Anyone can buy a newish house and rent it. Put in the extra effort and buy a project to reno & get more rent for your buck.

cbf with renos at the moment... looking to buy something ready to rent... or consider building if that worked out more profitable somehow...

Buying off the plan can work out better however you'll have to wait until it's built. Buying a house and renting to a family could give a better rent:mortgage ratio than an inner-city apartment to a single person.

Speaking of houses, got any tips for good areas to buy an investment property Alex? Jess suggested Altona Meadows, anywhere else? Tarneit any good?

Yeh depends what your after - I wouldn't go altona meadows myself i think seabrook has potential can get a good size block with a house on it for under $400k surrounded by suburbs that similar blocks cost $300k+ alone

With so many people trying/doing exactly the same thing (buy, rent out, negative gear, buy again) where will the market go? The rental market is flooded with houses at the moment, a lot of them overpriced because people need the money to pay off the mortgage.

If rent is so much cheaper in the CBD than the burbs, i think rental prices are going to spread from the cbd outwards and shrink purely because there are so many investment properties & town houses popping up. Especially when a lot of older folks are trying desperately to make up for their lack of super. That plus foreign money snapping up properties... Somethings gotta give in the next few years.

I reckon every 3rd-4th house i inspected last month had a for lease sign before even the For Sale sign had been taken down. It doesnt look good because you know the owners havent done much/anything to the house and are possibly going to be tighter than a ducks butt when it comes to costs.

lol @ the block first world problems ... My owners would be doing back flips to get 10k, 40k over reserve! Shit even to get reserve!

101%

mopst of my properties that go to auction do not hit reserve.

Speaking of houses, got any tips for good areas to buy an investment property Alex? Jess suggested Altona Meadows, anywhere else? Tarneit any good?

Altona North, right on the border of Williamstowm/Newport has a few bargains left over your side if you want to play the capital gains game...

rent it for a larger sum which puts it close to the mortgage repayment.

This is hard to achieve without extensive work done by yourself (then you have to value your own time)... Even interest only

Hi jezza

How's the band going

Thought the same.... lol'd

Strongly advise not to buy off the plan apartments / land etc

This.

Yeh depends what your after - I wouldn't go altona meadows myself i think seabrook has potential can get a good size block with a house on it for under $400k surrounded by suburbs that similar blocks cost $300k+ alone

Have you tried to drive in and out of Seabrook? It takes me almost half an hour to drive from Altona Meadows to Seabrook Blvd after work and it's like 5km...

tried newish burger joint in Huntingdale: Burgled.

burgers are under $15 and were pretty tasty.

Had a japanese-style? fried chicken burger with asian slaw and wasabi aioli. $11. quality sweet roll. do recommend.

next SAU monthly meet. they open late and huntingdale is dead after hours. plenty of parking.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
    • It's amazing how well the works on the leather seats. Looks mint. Looking forward to see how you go with the wheels. They do suit the car! Gutter rash is easy to fix, but I'm curious about getting the colour done.
×
×
  • Create New...