Jump to content
SAU Community

Recommended Posts

I stand corrected.

Presenting the gangsterest mother f**ker to emit wifi

http://www.centrecom.com.au/netgear-r8000-nighthawk-x6-ac3200-tri-band-wi-fi-router-

Will buy.

nighthawk x6 or gtfo when it comes to wifi routers these days. Wait for sales. They drop to $270ish. Officeworks will price match.

Yeah but thats coz it's old as well, so it works well with the old router telstra gave me... It's wireless G...This card can connect but doesn't work at it's potential with an old router, so a new router should fix it...My parents have a wireless-N router here and it's working fine...was working fine at centercom too...

Telstra want $216 for their AC router, that porno bad boy is $339....Once I've seen something I want, it's very hard for me to buy a lesser product lol

ive got the telstra AC router and the older N router. The N router modem gives me faster internets so I offload routing to a nighthawk

That what you run birds isn't it? how you rate them?

Was also looking at invos..

Nah I run Toyo R1R...bit more exxy but they are an all weather rather than summer semi

Have you considered something in the cisco range? Not that expensive when you look at the long term benefits....

prod_large_photo0900aecd800d697a.jpg

Would also need to purchase a separate unit to do wireless though...

  • Like 1

Cool. How come you went with 265/40 instead of 35?

They grippy?

Yeah I brought the wrong ones so dont fit at the front only rear lol

Grippy enough for my power. Havent tracked them yet tho, but I hear its up there with the ad08s

look if we have kids I will be re-evaluating my job for sure.

but for now. why would I.

now Katie's back is good again, get her to come on a few work trips with me will be even better.

trying too hard for kids?!?

if-you-know-what-i-mean-127.png

  • Like 1

Fuark I think I just heard some guy's asshole rip apart in the cubicle next to me

Massive explosion and bombs dropped followed by the sound of...sobbing/crying? WTF

Then using what I suspect was the toilet brush to push it all down while flushing

  • Like 1

Fuark I think I just heard some guy's asshole rip apart in the cubicle next to me

Massive explosion and bombs dropped followed by the sound of...sobbing/crying? WTF

Then using what I suspect was the toilet brush to push it all down while flushing

genuine lulz

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
×
×
  • Create New...