Jump to content
SAU Community

Recommended Posts

With higher risk and likely worse rates.

No one (virtually) is going to lend at 95% without LMI which at $400k will slug you an extra $8-10k

As an investment property that you may want to sell at any time depending on the market it is unwise to gear it so highly. For an owner/occupier it's more logical as you intend to live there for a while.

Higher LVI mean higher interest repayment which as an investment property means larger negative gearing.

For high income earners better to negative gear for that tax refund.

The housing market is where Al and I swap. Here he's all "spend spend spend, don't worry about the future" and I'm 100% conservative.

Lol

couldn't be further from the truth - I do it for a living (& well shameless free plug). However if you ever spoke to me about it my opinions would surprise you

I'm about the most financially conservative person you'll find hence why I'll pay my house off in 5 years max Id say & until I own mine 100% I won't be buying anything else for speculative purposes chances are I won't invest in property at all but maybe I know to much.

Is there many fees involved in moving?

Just a couple of hundred

And normally the other bank will rebate it for you

If anyone wants to move to NAB, i have a contact person that originally gave me the 4.45% rate

Everything of mine is with cba, credit cards 2 savings accounts, home insurance, loan protection etc etc so if these mother f**kers don't wanna play ball I'll cancel everything

same here; look into

https://www.commbank.com.au/personal/home-loans/wealth-package.html

https://www.commbank.com.au/content/dam/commbank/personal/home-loans/fact-sheets/Wealth_Package.pdf

edit: there you go, package it all up;

10% off home insurance, 5% off loan insurance, 0.6% off interest rate, No CC fee & request Diamond for that $$ status.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...