Jump to content
SAU Community

Recommended Posts

  • Replies 41
  • Created
  • Last Reply

Top Posters In This Topic

6k should be heaps mate, check out gum tree for 180s and s13s. theres tones on there and on hardtuned.net

ive seen very clean 33 gtsts sell for 6k low kms great nick (my friends) so you should get a non turbo for that price!

also dont forget to factor in insurance and rego :)

Non turbo skylines are usually more expensive due to them being more rare, but mostly due to P plater demand.

A non turbo skyline in good nick will go from 8k to 12k (if your talking r33).

Hell my r33 GTS cost 12 grand 3 years ago and I just bought my gtst with double the power for much less.

Like Ruxis said, gumtree will have alot of them but you can't go wrong with carsales either.

Prepare to spend double that to get an S13 or R32 into smooth running condition.

I bought my S13 for 6.5k. I only replaced the parts necessary and that figure ended up doubling.

Given that, my S13 was immaculate, if you buy one in bad condition be prepared to spend a lot more to get it up to stratch.

I've searched gumtee and carsales for the past few months, and no S13 silvia on there is worth buying given their condition.

Your best bet would be a late model R33....then sell that when you get your full licence.

No he doesn't, or he'd have said a Ti. Ti= SSS without the badge or insurance policy high prices.

but the badge is important for young blokes

It's like when I was in primary how I'd get pissed off my mum would buy me lynx shoes when I wanted nike air max :yucky:

I've been watching for S13's and 180's for my P-plate son for a while. Not many out there and yes, a few $k more and needing work. They are just getting older now.

We went to look at a couple of preludes too around $5k and they needed work as well.

I'd strongly suggest that you budget an extra $1k when looking at older used cars just to take care of odds and ends that will need to be sorted.

Good luck with the search though.

id buy a little run around, and save for the turbo version when youre off your p's.

but, if you do want it now, search for the neatest car you can for the price, that way you can get a decent resale value.

hope this helps.

good luck.

The car that you look at should be dictated that how far you're stretched with the $6k in your wallet. Are you bang on $6k when you get a car or do you have room to move north of that?

Bear in mind that a $6k car will never be just $6k. You need to factor in other sunk costs as well such as insurance and rego. Also there will always be something that needs to be fixed on top of the car price. If you DIY, great cause you can save money. If not, then another money sink hole.

I got my 33 gtst for a great price and it came as clean as they come nowadays. Having said that I still had to put in extra money on top of the price to get a few things totally neat.

If you're on the Ps, might be a good idea to get a little run-about that you can have a bit of fun with for the time being. Once you're off your Ps, then you can go wild, and by then you'll have more coin and cars that you want are even cheaper.

In all honesty it's not worth going NA anything, pain in the neck to convert everything over if u want to go turbo (or better, wastelanders no what I'm on about). Rb20 natros are painfully slow same can be said for ca18s, best bet is a natro sr20 or late natro rb25 32.

If I had my time again I'd stick with my daily and not buy my natro 33.... But it's up to u man.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
×
×
  • Create New...