Jump to content
SAU Community

Recommended Posts

Hi all,

I'm currently in the market for a good R32 GTR. Most rebuilt vehicles having forged pistons, rods, racing bearings tend to go for around $20-22k, while cars with stock internals can go from $15-16k.

I'd be happy with around 300kw atw and the car will only be used as a weekender; never planning to track it. Is it worth forking out the extra $5-6 for something with forged internals in my case?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/453580-worth-buying-forged-gtr/
Share on other sites

It's quite easily worth forking out 5-6k for a well built all round car. A forged engine doesn't always align itself With a quality car.

Like stated above if 5-6k worries you then maybe it's not the right choice, the more you cheap out with these things the more it will

Cost you in the long run.

"The poor man pays twice"

  • Like 1

The answer is yes, but not because it has forged pistons. It is worth paying extra for a car that has been competently reconditioned reasonably recently and for which there is evidence in the form of receipts, dyno sheets, maybe a compression test, road test and examination by someone who knows what to look for. If you can get a well looked after car then its is likely that the clutch is good, brakes and suspension have been properly maintained etc. GTR owners will tell you that they are money pits and if you can avoid expensive repairs soon after purchase so much the better.

  • Like 1

Its a GTR, expect it to cost money!

I'd be more concerned about getting a car without rust than one with a built motor. Engines can be replaced but rust had a tendency get worse before you realise that its really bad.

Hi all,

I'm currently in the market for a good R32 GTR. Most rebuilt vehicles having forged pistons, rods, racing bearings tend to go for around $20-22k, while cars with stock internals can go from $15-16k.

I'd be happy with around 300kw atw and the car will only be used as a weekender; never planning to track it. Is it worth forking out the extra $5-6 for something with forged internals in my case?

Cheers

I think when you talk about forged internals you really just mean a rebuilt motor. Yeah sure most people use forged pistons as they are cheap these days but for 300kW there is nothing wrong with Nissans pistons. In fact their ring package has much to recommend itself.

Anyway old story: Buy a nice one. If it has a rebuilt motor, good. If it doesnt thats fine too. But buy the car, not the spec.

  • Like 2

looks nice enough...do a proper compression test as a minimum....get underneath it and check all suspension bushes and diff bushes etc....check structure for rust...also check chassis rails for damage (common for them to be jacked up off the chassis rail)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...