R.3.2.G.T.R Posted November 6, 2022 Share Posted November 6, 2022 On 1/11/2022 at 12:50 PM, The Mafia said: Just an update. I have the 8474 on the engine now (8374 previously) It's about 100-200rpm laggier and makes an absolute sh$t tonne more power up top. The 8374 topped out at 650rwhp at 30psi. This 8474 is just f$c%ing dumb. At 26psi, it's making well and truly over 750rwhp and just keeps going. It doesn't fall over. RB28 with Vcam (264/272), 6boost manifold, 3.5inch exhaust, E85, Emtron KV8 etc etc Which rear housing with 8474? Link to comment https://www.sau.com.au/forums/topic/466636-borg-warner-efr-series-turbos-v-20/page/140/#findComment-7972147 Share on other sites More sharing options...
The Mafia Posted November 6, 2022 Share Posted November 6, 2022 1 hour ago, R.3.2.G.T.R said: Which rear housing with 8474? I reused my 8374 rear housing, it's a twin scroll 1.05 rear housing Link to comment https://www.sau.com.au/forums/topic/466636-borg-warner-efr-series-turbos-v-20/page/140/#findComment-7972150 Share on other sites More sharing options...
RB335 Posted November 8, 2022 Share Posted November 8, 2022 (edited) The issue with my 8474 was it did fall over in the top end it was struggling thats the only reason i removed it, I do recall the car had some odd rough running the more i drove it which i mistaked for the turbo, or drop in exhaust cam hurting flow so couldn't really get it to run how it should, but response wise I could get it on almost right off the lights with a gradual clutch drop most wow factor out of any EFR turbo i've tried zero lag getting back on throttle this was 1.05 rear great turbo for fast street driving Edited November 8, 2022 by RB335 Link to comment https://www.sau.com.au/forums/topic/466636-borg-warner-efr-series-turbos-v-20/page/140/#findComment-7972254 Share on other sites More sharing options...
Shoota_77 Posted November 8, 2022 Share Posted November 8, 2022 2 hours ago, RB335 said: The issue with my 8474 was it did fall over in the top end it was struggling thats the only reason i removed it, I do recall the car had some odd rough running the more i drove it which i mistaked for the turbo, or drop in exhaust cam hurting flow so couldn't really get it to run how it should, but response wise I could get it on almost right off the lights with a gradual clutch drop most wow factor out of any EFR turbo i've tried zero lag getting back on throttle this was 1.05 rear great turbo for fast street driving Would have been an awesome comparison to see how it went throwing on the 1.45 turbine housing. Presumably that would have given you more top end but obviously at the expense of a bit of response. When you say falling over in the top end, at what power was that? Link to comment https://www.sau.com.au/forums/topic/466636-borg-warner-efr-series-turbos-v-20/page/140/#findComment-7972256 Share on other sites More sharing options...
burn4005 Posted November 8, 2022 Share Posted November 8, 2022 We're you running a screamer or plumbed back? These turbos need to wastegate like 25-30% of the exhaust flow so it can make quite a big difference once you factor in expansion ratio -> emap -> VE Link to comment https://www.sau.com.au/forums/topic/466636-borg-warner-efr-series-turbos-v-20/page/140/#findComment-7972264 Share on other sites More sharing options...
SLVRBAKSLPZ Posted November 8, 2022 Share Posted November 8, 2022 I ended up getting a full turbo kit from spectrum motorsports from Canada. I went with the 9280. itll be a bit for install as im painting my car and motor rebuild. Link to comment https://www.sau.com.au/forums/topic/466636-borg-warner-efr-series-turbos-v-20/page/140/#findComment-7972267 Share on other sites More sharing options...
RB335 Posted November 9, 2022 Share Posted November 9, 2022 (edited) Had twin Tial MV-S 38mm gates with Y pipe plumbed back into a 3.5" dump EFR9180 held power fine 8474 began dying up top, I had limited time to do more dyno runs so only did one test but quite a bit of street driving on both turbos. OK no problem i will try vent them to atmosphere next time see how it effects it will have much more sensors all over the engine on next motor too for monitoring stuff on manifold. I have no access to an engine or dyno at the moment Mafia you are interested i can send you my 9180 then cover freight back to me you can test it lots of tech talk etc but test ok. Edited November 9, 2022 by RB335 Link to comment https://www.sau.com.au/forums/topic/466636-borg-warner-efr-series-turbos-v-20/page/140/#findComment-7972288 Share on other sites More sharing options...
burn4005 Posted November 9, 2022 Share Posted November 9, 2022 (edited) a 3.5" plumbed back exhaust with an 8474 on kill would have had sky high EMAP. screamers would add loads of power through VE improvement and pumping loss reduction. at that kind of compressor power you'd be at expansion ratios of 3.5:1 or more on the turbine, so every PSI of backpressure would be 3.5+psi in the manifold. Edited November 9, 2022 by burn4005 Link to comment https://www.sau.com.au/forums/topic/466636-borg-warner-efr-series-turbos-v-20/page/140/#findComment-7972289 Share on other sites More sharing options...
The Mafia Posted November 9, 2022 Share Posted November 9, 2022 12 minutes ago, RB335 said: Had twin Tial MV-S 38mm gates with Y pipe plumbed back into a 3.5" dump EFR9180 held power fine 8474 began dying up top, I had limited time to do more dyno runs so only did one test but quite a bit of street driving on both turbos. OK no problem i will try vent them to atmosphere next time see how it effects it will have much more sensors all over the engine on next motor too for monitoring stuff on manifold. I have no access to an engine or dyno at the moment Mafia you are interested i can send you my 9180 then cover freight back to me you can test it lots of tech talk etc but test ok. I would say the 74mm turbine would have been at it's limit and the pressure ratio across the engine would have started to go up. The 9180 has the bigger rear which will flow a lot more before choking up. haha do you trust me enough to send me a turbo? I have access to a dyno but it's a bit of a big job to swap them over Link to comment https://www.sau.com.au/forums/topic/466636-borg-warner-efr-series-turbos-v-20/page/140/#findComment-7972290 Share on other sites More sharing options...
SLVRBAKSLPZ Posted April 28, 2023 Share Posted April 28, 2023 Any recent dyno results of a 9180 or 9280?? Link to comment https://www.sau.com.au/forums/topic/466636-borg-warner-efr-series-turbos-v-20/page/140/#findComment-7978834 Share on other sites More sharing options...
Lithium Posted May 3, 2023 Share Posted May 3, 2023 (edited) On 29/04/2023 at 1:47 AM, SLVRBAKSLPZ said: Any recent dyno results of a 9180 or 9280?? Not an RB, but the nost recent result I've seen, and one of the more impressive is this 3litre VVTi 2JZGTE making 1130hp @ hubs with 30psi by 4000rpm on an EFR9280: https://fb.watch/kiHcr8Bydb/ Edited May 3, 2023 by Lithium 3 Link to comment https://www.sau.com.au/forums/topic/466636-borg-warner-efr-series-turbos-v-20/page/140/#findComment-7978963 Share on other sites More sharing options...
Full-Race Geoff Posted May 4, 2023 Share Posted May 4, 2023 On 4/28/2023 at 6:47 AM, SLVRBAKSLPZ said: Any recent dyno results of a 9180 or 9280?? EFR turbos have largely been unavailable for the last 18 months so until BW resumes production its likely going to be pretty quiet 1 Link to comment https://www.sau.com.au/forums/topic/466636-borg-warner-efr-series-turbos-v-20/page/140/#findComment-7978995 Share on other sites More sharing options...
Lithium Posted May 8, 2023 Share Posted May 8, 2023 On 05/05/2023 at 5:42 AM, Full-Race Geoff said: EFR turbos have largely been unavailable for the last 18 months so until BW resumes production its likely going to be pretty quiet Any idea if some of the SX-R upgrades are going to flow over the to EFR range? The compressor map for the S200SX-R 7670 (/ S258SX-R?) looks like a cracker and could only imagine similar aero would make a worthy and needed update for the EFR7670: 2 Link to comment https://www.sau.com.au/forums/topic/466636-borg-warner-efr-series-turbos-v-20/page/140/#findComment-7979168 Share on other sites More sharing options...
welshy_32ZILA Posted May 14, 2023 Share Posted May 14, 2023 Hi, Me again. Long time between drinks Any chance anyone would have a 1.45 ar rear housing interested in swapping for a 1.05 to suit a 8474? Turbo is choking Uptop and keen to see with a gearbox change how a 1.45 would respond. Link to comment https://www.sau.com.au/forums/topic/466636-borg-warner-efr-series-turbos-v-20/page/140/#findComment-7979430 Share on other sites More sharing options...
RB335 Posted May 26, 2023 Share Posted May 26, 2023 (edited) I'm also after a 1.45 suit a EFR9180 / 9280 if anyone has Edited May 26, 2023 by RB335 1 Link to comment https://www.sau.com.au/forums/topic/466636-borg-warner-efr-series-turbos-v-20/page/140/#findComment-7979905 Share on other sites More sharing options...
Full-Race Geoff Posted May 30, 2023 Share Posted May 30, 2023 Full Race stocks the 1.45 a/r turbine housing, can ship immediately if you're in need. Link to comment https://www.sau.com.au/forums/topic/466636-borg-warner-efr-series-turbos-v-20/page/140/#findComment-7980056 Share on other sites More sharing options...
The Mafia Posted July 20, 2023 Share Posted July 20, 2023 On 31/05/2023 at 3:24 AM, Full-Race Geoff said: Full Race stocks the 1.45 a/r turbine housing, can ship immediately if you're in need. Hey mate, any specials for the SAU team? I have an EFR 8474 Black series on my RB28 and it has the 1.0AR rear. I think it's choking up. Do you have any back to back dynos / comparisons of the smaller and larger rears? Link to comment https://www.sau.com.au/forums/topic/466636-borg-warner-efr-series-turbos-v-20/page/140/#findComment-7981332 Share on other sites More sharing options...
Full-Race Geoff Posted July 20, 2023 Share Posted July 20, 2023 16 hours ago, The Mafia said: Hey mate, any specials for the SAU team? I have an EFR 8474 Black series on my RB28 and it has the 1.0AR rear. I think it's choking up. Do you have any back to back dynos / comparisons of the smaller and larger rears? Depending on how high you rev the 2.8, and your boost level - choking can happen with 1.05 a/r. If you can log turbo speed and backpressure it's insightful into making a change. The 1.45 a/r back to backs are deceiving - on the steady state dyno they look like identical spool. but on the street, its anywhere from 150-400rpm later spool depending on gear. I'd be happy to crunch the #s for a match if you wanted to know what the calculations show? Link to comment https://www.sau.com.au/forums/topic/466636-borg-warner-efr-series-turbos-v-20/page/140/#findComment-7981354 Share on other sites More sharing options...
Shoota_77 Posted July 20, 2023 Share Posted July 20, 2023 4 hours ago, Full-Race Geoff said: Depending on how high you rev the 2.8, and your boost level - choking can happen with 1.05 a/r. If you can log turbo speed and backpressure it's insightful into making a change. The 1.45 a/r back to backs are deceiving - on the steady state dyno they look like identical spool. but on the street, its anywhere from 150-400rpm later spool depending on gear. I'd be happy to crunch the #s for a match if you wanted to know what the calculations show? It would be massively appreciated if you could please fudge the figures to make it look like spool up is 1500 rpm later and it only makes 2 HP difference? That would instantly save me spending $1600 for something that will sit on a shelf for the next 2 years.... 1 Link to comment https://www.sau.com.au/forums/topic/466636-borg-warner-efr-series-turbos-v-20/page/140/#findComment-7981356 Share on other sites More sharing options...
The Mafia Posted July 21, 2023 Share Posted July 21, 2023 9 hours ago, Full-Race Geoff said: Depending on how high you rev the 2.8, and your boost level - choking can happen with 1.05 a/r. If you can log turbo speed and backpressure it's insightful into making a change. The 1.45 a/r back to backs are deceiving - on the steady state dyno they look like identical spool. but on the street, its anywhere from 150-400rpm later spool depending on gear. I'd be happy to crunch the #s for a match if you wanted to know what the calculations show? At the moment I am running 20-24psi and rev it to 7,000rpm on the circuit. I have a Holinger 6speed so there isn't a great need to rev it hard, only keep the rpm above 4500rpm or it bogs a little. It's a 9.75:1 compression ratio with a HKS Vcam. 264/272 cams. It's a hard one for me. 150rpm I can live with, but 400rpm would hurt a little in two corners that I know. I plan to put it in the dyno soon and measure the back pressure through one of the EGT ports. I have plenty of logs and data, and I mean lots of data. I also have turbo speeds. Running between 104,000rpm and 108,000rpm. Link to comment https://www.sau.com.au/forums/topic/466636-borg-warner-efr-series-turbos-v-20/page/140/#findComment-7981364 Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now