Jump to content
SAU Community

Can you daily an EVO?

Gymkhana

By Gymkhana,
in General Automotive Discussion

 Share

Recommended Posts

Scott Black Rising Star

Scott Black

Posted
Posted

Depends how much you like your licence. They drink alot less than a skyline yet even stock they are rather difficult to avoid speeding in at times.
When stock from a comfort point of view they are very similar to a standard Lancer so very easy to daily.


Deza3000 Proficient

Deza3000

Posted
Posted (edited)

I drove mine daily for 3 years. Mind you it was close to stock for the majority of the time i had it, then put out roughly 250awkw in the final 6 months prior to selling on a standard exedy heavy duty clutch. Easy to drive, some can get a little clunky depending on whether the transfer case bushes are worn to shit. Very good throttle response, very easy to speed. Cheapish to maintain. Theft rate seems to be climbing for evos though causing insurace prices to be almost equal to a GTR

 

Edited by Deza3000
Gymkhana Enthusiast

Gymkhana

Posted
  • Author
Posted (edited)
12 hours ago, Hadouken said:

Lots of people daily evos. I wouldn't daily mine. I travel 1,000km a week though.

How many k's you doing a week?

And which evo are we talking?

I'm in the same boat, just under 800KM a week. I don't think it's worth it as I will rack up K's far too quickly.

Edited by Gymkhana
MUFASA Enthusiast

MUFASA

Posted
Posted

Depends on the EVO I reckon. I have a X and with the SST gearbox I think it's the perfect daily and can do a few laps around the track on the weekend.
I do about 500 kms a week and I bought the car new in 2013, it still feels just like it did on day one.
The car is also no stranger to the tracks as it goes to Sandown probably every 3 months and with just basic mods was enough to do a few 1.24/25 laps.
The older EVO's I think feel a lot more raw (and fun), but having to change gears all the time in stop start traffic might start to get a bit tiring a few months down the line...then again, I am probably getting old and soft, hence why I think that.

Deza3000 Proficient

Deza3000

Posted
Posted (edited)

Have you considered a ralliart? Assuming its just a daily it would be cheaper to run and you wont feel as guilty clocking on a few ks on them, it uses the same evo 10 motor and trans, its just heavily detuned. Or if you're doing 1000ks a week just get a 2013 falcon/commodore, pretty cheap and most cabs run them past 300,000ks.

Edited by Deza3000
  • Like 1
  • 4 months later...
Odium Grand Master

Odium

Posted
Posted

I used my VII as a daily until January when it was stolen, it was a bit rougher than I would have liked (depending on who was with me... got a few complaints about the hugging recaros from ladies with hips).

I just couldn't bare to drive a corolla orollaor something :P No Regrats!

  • 6 months later...
  • 4 years later...
luke gtr Grand Master

luke gtr

Posted
Posted

Bumping an old thread for others with similar questions. 

 

Daily an X MR is very nice.

Sat nav, heated seats, cruise control, auto lights and wipers, proximity start and entry, there's a LOT to like.

Are they as fun as the older models?

Not sure, never had the chance to drive an older gen. But, I've now got a second X which I'm not dailying purely to keep the kms down.

 

Keep in mind, I had a 32 gtr with a china gt42 and a has dog box that I used as a daily, so it all comes down to how comfortable you want to be.....

  • Like 1
luke gtr Grand Master

luke gtr

Posted
Posted
On 22/04/2022 at 10:50 PM, niZmO_Man said:

Wasn't that the point of them? Especially the 'auto' version? I remember reading about WRX vs. Evo and the Subaru interior/daily drive-ability was praised compared to Evo.

Wrx should be compared to the ralliart lancer.

The evo should be compared to the sti.

Having driven both(of the same era) the sti and evo really are much of a muchness.

But, only driven the sti in a manual, and the evo in the sst("auto").

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      Did you panel beat the dents or have you tried to repair this only using filler?  Is your sanding block soft/flexible and is following the shape of the panel rather then just knocking down the high points? 
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      I haven't knocked them down yet. I think I made the repair more complex than it should have been. I had rock chips combined with waviness and dents and I tackled it all in one because it was near each other and just end up wasting a bunch of bog lol. I'll knock down those areas and see how I go. And yep what you are saying at the end is correct. I think I might be sanding the top of a steep hill then my sanding block falls into the dent and gets rid of the guidecoat if that makes sense. Though shouldnt unless I'm covering too big of an area with not a long enough block. I'll try something new and provide some updates. Getting there though! Thanks as always.  
    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      Yeah makes sense, hard to comment on your situation without seeing what your doing. I was talking generally before, I would not be looking to randomly create low spots with a hammer to then have to fill them.  It's hard without seeing what your doing, it sounds like you are using the guide coat to identify low spots, as you're saying the panel is still wavy. I don't see how you're not ending up with patches of guide coat remaining in a wavy panel? Once the high spots are knocked down to the correct level, surely to have a wavy panel you need low spots. And those low spots would have guide coat still in them?
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      So I'll put filler past the repair area a bit to make sure I don't miss anything. Then I'll block it until it's almost level, put the guidecoat, then keep blocking until it's gone. Then it's still wavy.  In regards to hitting the panel, I saw this video might give more context - Skip to 0:47 he knocks it down. But yeah I'm sanding until the guidecoat is gone then checking because otherwise my filler is still well above the bodyline. Unless what you're saying is I should put guidecoat around it early, surrounding the filler then stip once it's gone?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      I refreshed the OEM injectors with the kit and connected it up. It now ideals okay even with the IACV removed. Driving still has the same cutoff issue like the 550cc injectors so the issue is somewhere else. I bought FPG's Fuel Pump Hanger. I will be installing it next, but it is not as straightforward as I thought it was with my limited wiring knowledge and no instruction on the specific model I purchased (FPG-089). I also got the incorrect billet clamp as I could not find info on the OEM sizing.
×
×
  • Create New...