Jump to content
SAU Community

Recommended Posts

49 minutes ago, hy_rpm said:


Offt! shitbox
Almost a $50k build i wouldnt sell it not worth it

Is there a sneaky 3.2L stroker here you aren't telling us about?! ?

2 hours ago, Dose Pipe Sutututu said:

Decided to update my spreadsheet, turns out "cheap shit box project" isn't so "cheap" after all.

 

image.png.fad6f261960df98643a49e6f825b0bed.png

At least you arent in denial about what you have spent lol

20 minutes ago, admS15 said:

Im clearly doing it wrong... Still below 20k brah.

Not including consumables like brake pads and tyres.

Mine doesn't include tyres, pads, maintenance shit either :(

 

Keys were handed to a mate whilst it was in New Delhi. Safe to say the clutch, gearbox and engine seem to be working well.

 

  • Like 4
12 hours ago, V28VX37 said:

8/10

Would have been 9 but needs more gauges

More like needs a working tacho Hahah.. At present rev limiter is at 8300rpm soft cut and 8500rpm hard cut.

#becausehonda 

  • Like 1

Gifts run pre Lunar New Year (yes I'm Asian and no I won't go back to my country becasue I'm already here ?).

Still no time to throw it on the dyno yet but AFRs are in the low 11s and timing isn't anywhere even barely close to a stock map (actually used my old map and flatten the timing due to cams).

20180215_105354_Burst01.thumb.jpg.598d2b223ec53e5500a27610a90f44dd.jpg

  • Like 2
5 hours ago, Dose Pipe Sutututu said:

Gifts run pre Lunar New Year (yes I'm Asian and no I won't go back to my country becasue I'm already here ?).

Still no time to throw it on the dyno yet but AFRs are in the low 11s and timing isn't anywhere even barely close to a stock map (actually used my old map and flatten the timing due to cams).

20180215_105354_Burst01.thumb.jpg.598d2b223ec53e5500a27610a90f44dd.jpg

All i can say is LOL. 

5 hours ago, Dose Pipe Sutututu said:

Gifts run pre Lunar New Year (yes I'm Asian and no I won't go back to my country becasue I'm already here ?).

Still no time to throw it on the dyno yet but AFRs are in the low 11s and timing isn't anywhere even barely close to a stock map (actually used my old map and flatten the timing due to cams).

20180215_105354_Burst01.thumb.jpg.598d2b223ec53e5500a27610a90f44dd.jpg

All i can say is LOL. 

Without an idle correction rate vs. timing compensation table, getting the car to idle this smoothly wasn't easy! Had to pull a few Microtech tricks haha

 

  • Like 1
9 hours ago, Dose Pipe Sutututu said:

Without an idle correction rate vs. timing compensation table, getting the car to idle this smoothly wasn't easy! Had to pull a few Microtech tricks haha

 

y u no lumpy

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
    • yeh they are 235/45/17 up front and 255/40/17 in the rears. I still didn't get my answer if i can fit a 18x9 up front. I want to get 4 of this and see if they will fit before committing as they didn't see an 18x8 as an option but there is a 18x9.5 also.   Enkei RS05-RR 18x9 35mm ET 5x114.3 75.0 Bore Matte Gunmetal Wheel
    • This. The R34 handbrake icon DOES come up when the brake fluid level is low. You might be sitting right on that threshhold. I have been down this diagnosis path and this was the solution (and it was pretty much as full as your picture is to begin with).
×
×
  • Create New...