Jump to content
SAU Community

Recommended Posts

49 minutes ago, hy_rpm said:


Offt! shitbox
Almost a $50k build i wouldnt sell it not worth it

Is there a sneaky 3.2L stroker here you aren't telling us about?! ?

2 hours ago, Dose Pipe Sutututu said:

Decided to update my spreadsheet, turns out "cheap shit box project" isn't so "cheap" after all.

 

image.png.fad6f261960df98643a49e6f825b0bed.png

At least you arent in denial about what you have spent lol

20 minutes ago, admS15 said:

Im clearly doing it wrong... Still below 20k brah.

Not including consumables like brake pads and tyres.

Mine doesn't include tyres, pads, maintenance shit either :(

 

Keys were handed to a mate whilst it was in New Delhi. Safe to say the clutch, gearbox and engine seem to be working well.

 

  • Like 4
12 hours ago, V28VX37 said:

8/10

Would have been 9 but needs more gauges

More like needs a working tacho Hahah.. At present rev limiter is at 8300rpm soft cut and 8500rpm hard cut.

#becausehonda 

  • Like 1

Gifts run pre Lunar New Year (yes I'm Asian and no I won't go back to my country becasue I'm already here ?).

Still no time to throw it on the dyno yet but AFRs are in the low 11s and timing isn't anywhere even barely close to a stock map (actually used my old map and flatten the timing due to cams).

20180215_105354_Burst01.thumb.jpg.598d2b223ec53e5500a27610a90f44dd.jpg

  • Like 2
5 hours ago, Dose Pipe Sutututu said:

Gifts run pre Lunar New Year (yes I'm Asian and no I won't go back to my country becasue I'm already here ?).

Still no time to throw it on the dyno yet but AFRs are in the low 11s and timing isn't anywhere even barely close to a stock map (actually used my old map and flatten the timing due to cams).

20180215_105354_Burst01.thumb.jpg.598d2b223ec53e5500a27610a90f44dd.jpg

All i can say is LOL. 

5 hours ago, Dose Pipe Sutututu said:

Gifts run pre Lunar New Year (yes I'm Asian and no I won't go back to my country becasue I'm already here ?).

Still no time to throw it on the dyno yet but AFRs are in the low 11s and timing isn't anywhere even barely close to a stock map (actually used my old map and flatten the timing due to cams).

20180215_105354_Burst01.thumb.jpg.598d2b223ec53e5500a27610a90f44dd.jpg

All i can say is LOL. 

Without an idle correction rate vs. timing compensation table, getting the car to idle this smoothly wasn't easy! Had to pull a few Microtech tricks haha

 

  • Like 1
9 hours ago, Dose Pipe Sutututu said:

Without an idle correction rate vs. timing compensation table, getting the car to idle this smoothly wasn't easy! Had to pull a few Microtech tricks haha

 

y u no lumpy

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
    • Yeah - I mean, go the other way. Smaller range. Not larger.
×
×
  • Create New...