Jump to content
SAU Community

Recommended Posts

3 hours ago, Dose Pipe Sutututu said:

I am back from 1 month of no SAU and car shit

Adaptronic is coming out, and is now for sales. $800 for SAU members $850 for Facebook or Scumtree or eScum

Ahh how good is it to have a month off.... (congrats by the way kent!!)

Why the move to a Halaltech?

2 hours ago, dr phil said:

Not going an Adaptronic modular, or an EMU Black?

As much as I support and recommend Adaptronic, a Haltech is so much faster to tune and get going when compared to an Adaptronic. The ECU Master range does look promising but never used it before, so means will need to spend time to acquaint myself with it. 

2 hours ago, timmy_89 said:

Ahh how good is it to have a month off.... (congrats by the way kent!!)

Why the move to a Halaltech?

Haha thanks man, part of the club now :)

I've outgrown the 440D Select and also over the idiosyncrasies involved with their software. Every time I set up the crank prime value it reverts back to a negative value approximately 4 to 6 starts, so these days I end up carrying the laptop with me to start the car lol.

Over night parts from Kudos Motorsports.

OEM wheel bearings all round, road safe ball joints all round and new washer motors because I like a clean windscreen lol.

34464030_240876389797466_2688695212863127552_n.thumb.jpg.d7357ee9411336a3571b50675b85ff73.jpg

 

So.... Had a few beers at work and accidentally ordered a few things.

AI SPR400, 1x DW200 lift pump, 1x more Wallahbro 460..

Hopefully no more fuelling issues ?

 

2 hours ago, Dose Pipe Sutututu said:

Do youse English? 

Wallah DW200 is lift, twin 460s feed!

Mashallah 

Who was english?

Did you order a stroker or you didnt hvae that many beers?

23 minutes ago, WantGTR said:

 

Who was english?

Did you order a stroker or you didnt hvae that many beers?

I'm not that dumb brah :)

Watch my little 2.5L motor thrash 2.6L fags with twins 

  • Like 2
So.... Had a few beers at work and accidentally ordered a few things.
AI SPR400, 1x DW200 lift pump, 1x more Wallahbro 460..
Hopefully no more fuelling issues [emoji28]
It is good to know that others do this. My Mrs is trying to convince me that late night / early morning orders from Plazmaman, rhd, amayama, etc. are a bad idea

Some parts to help my motor spin backwards and forget tunes ? 

Special shout out to Alanah and James at Game On Motorsports. Twisted my arm and ended up with an Elite 2500 and a 4 bar MAP sensor instead of me only just getting an Elite 2000 and using the onboard 3 bar MAP sensor lol.

20180616_133343.thumb.jpg.94a34d012a86a6fc67cf98ef91f98856.jpg

Currently car is at thr mechanic getting new wheel bearings and ball joints installed because I cbf doing it myself (although I have all the tools and access to my mate's press)

  • Like 3
26 minutes ago, hy_rpm said:

Planning on running more than 3bar boost?

Glad someone did the maths. I was going to get to it tomorrow if I had time.

  • Like 1
3 hours ago, hy_rpm said:

Planning on running more than 3bar boost?

You mean 2 bar of positive pressure, 3bar sensor needs to also read vacuum too :)

Also if you don't use the onboard MAP sensor you can use that to adjust the tune for atmospheric pressure changes 

Lastly I prefer the MAP sensor as close to the plenum as possible.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...