Jump to content
SAU Community

Recommended Posts

Lowering GTT Coupe / Coils & Springs

Alright gents, I need some genuine advice on something that must've been covered 1,000 times and I'm still hearing two arguments after doing some reading for the past two hours.

Objective: lower my stock R34 GT-T to maximum legal limit (legit, it's like a patrol at the moment)

Budget: $800-$1000 including install

Want: lowered look with comfort but not wanting race-quality stuff. Car is a daily and I do a lot of highway driving

Conflict: springs are cheap and will lower to what I want but will kill my shocks. Coilovers are great but don't necessarily want to spend 2k on suspension just for a daily

Really really unsure which way to go here, but I see a ton of lowered 33's around my town and they all go springs/shocks and have no complaints. I'm smart enough to know that the poor man pays twice so I need some suggestions with the above information.

Is there an in the middle option between spending bugger all on lowered springs to achieve what I want then getting smashed around and paying later for it, and entry level coilovers that'll probably do things I don't necessaryily need them to do? Thoughts?

 

Link to comment
https://www.sau.com.au/forums/topic/468278-lowering-gtt-coupe-coils-springs/
Share on other sites

If you just want it a little lower for looks, have a small budget, and aren't taking it racing, just put in lowering springs.

It won't "kill" your shocks, they just won't be matched perfectly to the springs anymore.....although in any case since it left the factory the springs will have sagged and the shocks will be slowly dying just from age so they aren't exactly what nissan intended any more anyway

Kings or Lovells or just about any equivalent coil springs.  Easy.

Best choice for dampers is a set of Bilstein B6s, especially if bought from SydneyKid as he sets them up to suit Skylines fairly well.  But....this will blow the budget, as the dampers are >$1k on their own.

So, read the damper thread again,

and then decide if you're happy to compromise on price and buy something that has twin tube innards, or if you want to stretch a bit more money for something single tube.  Your options include KYB and even some of the lower end Bilsteins.  It is my firm opinion that there has never been a decent damper manufactured here in Australia, so do not be tempted by Monroe, or Gabriel, even though they're probably no longer made here anyway.  Cheap shit is cheap shit no matter where it's made.

8 hours ago, niZmO_Man said:

KYB and your choice of off the shelf springs.

Don't supposed you could link me KYB'a for a 34/GT-T?

KYB part locator wasn't helpful and an eBay/net search gets me as close as an R33.

Im looking into a set of TEIN S lowering springs from the UK instead of the Kings.

You can probably find a set of nismo S-tune shocks and springs for pretty cheap these days.

I run them all round, low-ish, comfortable and stiff enough for twisty roads, you'll feel the limit of them at a track day though but it doesn't sound like that's what you're after so I'd add them to the list of options to consider.

20 minutes ago, Jordy32 said:

You can probably find a set of nismo S-tune shocks and springs for pretty cheap these days.

I run them all round, low-ish, comfortable and stiff enough for twisty roads, you'll feel the limit of them at a track day though but it doesn't sound like that's what you're after so I'd add them to the list of options to consider.

Still achieve the lowered legal limit and be okay handling-wise for what I need?

Might look into this if so!

NB: Teins from the UK we're gonna set me back $300 + $160 postage


Yep Jesse will do springs but can get exxy with shipping because heavy metal
29 minutes ago, Duncan said:

just buy local on this, it's not a top line motorsport application, just a slightly lower car. Kings, Lovells, whoever has them at your local repco....

That'll do the trick on stock shocks for now? I was thinking about springs on stock shocks for a month or two, then fitting some aftermarket shocks (KYB I'm yet to track down for a 34)

for sure, and even KYB is just an OEM replacement.  If you buy a set of specific shocks you will get the springs to match (or vice versa, but the point is they come as a set once they move too far outside standard parameters).

I ran lowered springs on stock shocks then KYBs for years on my 33 GTSt including track days and it was fine for a cheap upgrade. In fact probably better than most $1000-1500 spring and shock sets because they tend to use really cheap shocks and overly hard springs.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
×
×
  • Create New...