Jump to content
SAU Community

Recommended Posts

Built both heads up today. Only put Supertech valve stem seals in and OEM for the rest as there are no aftermarket springs or valves available for these.
YGuO1s.jpg
9MS9HR.jpg

I now have a 4 week delay on rod bearings from Japan so that's pretty much all I can do until the new year. 

  • Like 2

Not much of an update but painted N1 vents and parking stick thingo.
Also cut out the middle of the bumper to suit the new plates and gain more airflow as these like to run hot. 
DNMnMM.jpg

  • Like 1

Don't like how big and bulky the airbox is and the stupid sound suppression part that just collects sand!

Started off like this
peCZvn.jpg

Chopped it in half and then I was left with this nice flat surface to adhere the new mounting section to.
cXT4vI.jpg
mk1QFw.jpg

Also noticed that the round section actually sits outside the chassis rail in the wheel arch, so incorporated a cold air intake port into the new piece.
iCd4Rg.jpg


 

Airbox mod.jpg

  • Like 2
  • 2 weeks later...

Finished re-sleeving the whole harness tonight finally. What a mission but I think the outcome will pay off with a much neater engine bay. All I need to do is buy some larger clear heat shrink so I can branch the connectors off to where they need to go.

I won't tee it all off though until its on the engine as I might be able to re route some it to further neaten it up. 

EohFkE.jpg

 

Not Rywire or Chase bays spec but gives it that little extra professionalism. 

LVtyK5.jpg

 

Got the turbo back from getting rebuilt by MTQ as well. Shaft and cartridge journals were scored, some bent turbine fins and a small crack in the rear housing.

y3Hur4.jpg

 

The rod bearings are going to be here until January now, so when I get back from Holidays it's go, go, go!

Edited by Sack87
  • Like 2
  • 3 weeks later...
  • 2 weeks later...

I got the engine to a stage where I could bolt the gearbox back on and drop it on the subframe. I can easily roll it all out for the remaining work to do on it for ease of access. 
Had more delays in timing chains not being in stock locally and having to get them from Japan again and they won't be here until next weekend. Have some small bits coming from over East too which were supposed to be here by Friday but not coming until next Thursday, otherwise I would have bolted the whole lot back in the car. 

mbycOK.jpg

  • Like 2

Engine harness is all but done. A few little brackets to be made and two more connectors needed. It's 10x neater than what it was. 
j6LlNZ.jpg
aXmazm.jpg

Injector harness is almost fully tucked. 
wm1d1y.jpg

Degreased the engine bay as I'm 95% ready to bolt the engine up to the body. Someone else has already been in here before me. 
0bHSKY.jpg

  • Like 1
On 12/17/2018 at 8:26 PM, Sack87 said:

 

Got the turbo back from getting rebuilt by MTQ as well. Shaft and cartridge journals were scored, some bent turbine fins and a small crack in the rear housing.

y3Hur4.jpg

 

 

Can you tell us what you had done to the turbo? Looks like a bigger compressor wheel... steel/inconel turbine? Cost? Expected power? So many questions... :)

Looking good by the way!

Edited by andynogo
23 hours ago, andynogo said:

Can you tell us what you had done to the turbo? Looks like a bigger compressor wheel... steel/inconel turbine? Cost? Expected power? So many questions... :)

Looking good by the way!

It's a Billet Intense RS I bought from Scotty a few years ago. You'll find heaps of info on it in the turbo upgrade thread, but good for 500hp he says. 

  • Like 1
1 hour ago, Sack87 said:

It's a Billet Intense RS I bought from Scotty a few years ago. You'll find heaps of info on it in the turbo upgrade thread, but good for 500hp he says. 

Very good- should make some decent power! 

On 1/28/2019 at 7:53 PM, Akshunhiro said:

Looks like someone had the joy of swapping out the turbo!

Yep. Everything has silicone on it to seal it up, including water hoses onto pipes. I bought a dud... 

Got it bolted back this afternoon after doing heaps of little things around the engine that are hard to get to when it's bolted in. 

zwqoJ5.jpg

 

Still heaps of fiddly little shit to go though

5HhbTA.jpg

  • Like 5
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
×
×
  • Create New...