Jump to content
SAU Community

Recommended Posts

On 15/04/2019 at 9:43 PM, Tenny said:

Yeah definitely. I've never restored a car before and never tackled sound deadening before either. I'm only 25 so learning a lot as well. 

Just be careful not to hit it too hard and dint the floor :)

Sorry to hijack your thread  @Tenny  but I finally had some time so took the plunge and started removing the sound deadening in my R32. I used dry ice only. A couple of observations:

Initially I was being conservative but it was obvious after a short period of time not to skimp. If the covering isn't complete and thick enough, it won't cool rapidly.

Be patient. Not one of my traits but definitely required. Wait until you hear lots of cracks. I didn't need to hit it very often.

Cover larger areas if possible. It seems that the more you get to contract and freeze simultaneously the easier it is to remove. Makes sense I guess.

So what do people do next? I now see a lot of bare metal that I was intending on covering with sound deadening. Do people usually paint or apply a waterproof sealant? I am limited in terms of space, ventilation and ability so the simpler the better but that raw looking metal makes me nervous.

Thanks

Rob

15 hours ago, Robzilla32 said:

 

So what do people do next? I now see a lot of bare metal that I was intending on covering with sound deadening. Do people usually paint or apply a waterproof sealant? I am limited in terms of space, ventilation and ability so the simpler the better but that raw looking metal makes me nervous.

If you take a look at the LX Torana GTR thread, the owner has used a silver KBS on the inside of the shell which will then have sound deadener put on top.

At this stage im either thinking about repainting the interior the body colour or doing the KBS sealer. I'm unsure with the KBS whether it needs a bare metal to adhere to, or you could just scuff up the body with a scotch brite pad etc.

  • 2 months later...
  • 2 months later...

Been quite busy the last few months getting situated after purchasing my first home, so progress on the GTR has been slow.

With that being said, I dropped both 32s off to a fab shop to get some work done on the chassis rails of the GTR.

Is painful to post these photos but the work needed to be done! Unfortunately the gtr rails had the usual careless jacking damage etc that is common on 32s.

Photo dump below.

 

 

received_2215545188709097.jpeg

received_2147844138641440.jpeg

received_1715405425261958.jpeg

received_487251258878448.jpeg

received_2565605433697358.jpeg

Thankfully GTST's share the same rail sections and the red ones were in pretty good shape comparatively.

Rather than scrap the shell and waste good body sections we cut the rails out to use to repair the GTR. 

Everything has been taken back to bare metal with the replacement sections stitched in. Rust kill was extensively used and then primer sprayed on to combat rust for the time being.

As the shell will be going on a rotiserrie in the near future for blasting, the whole underside will be back to bare metal, cleaned up more, treated and then coated in a deadener / liner.

received_425559954797935.jpeg

received_527100004573238.jpeg

received_840676609717084.jpeg

received_864941170624017.jpeg

received_762998287526335.jpeg

received_2681723991923722.jpeg

received_855527534885125.jpeg

received_2278860465744972.jpeg

20200119_111348.jpg

20200119_111353.jpg

20200119_111405.jpg

20200119_111415.jpg

20200119_111427.jpg

20200119_111448.jpg

20200119_120347.jpg

  • Like 3

Quite happy with the new state of the rails, however they obviously arent absolutely perfect. I think you'd be hard pressed to find a 32 that does these days.

I also managed to swap the front end out of the gtst (rack, xmember, etc) for a GTR front reo that is pretty much perfect condition.

Got my eye on a few air compressors at the moment which i will eventually use for my home sand blast / powdercoating setup.

 

received_484590245575283.jpeg

  • Like 1

Wow, those rails were toast!  I’ve seen some bad ones but that takes the cake!  Looks heaps better after replacement. 
Look forward to seeing this all come together.

No rush, mine has been over 7 years!

  • Like 1
  • 2 weeks later...

Stumbled across a pair of genuine NISMO N1 rear pods...from the 3 piece set.

I'm assuming there was only ever 560 sets of these skirts made for the Nismo GTR's, can anyone confirm this?

I have confirmed that it is possible to cut down the length of the stock middle section of the factory skirts to fit the nismo rear pods, and the front pod is the same regardless, so I should be able to piece together the 3 piece skirts fairly easily. This is a score and a half :P

83680067_495878737978660_3906876593754079232_n.jpg

83872398_1551502578332467_7758060763192754176_n.jpg

83919875_530146054516813_4465818393500450816_n.jpg

Actually Nismo GTRs and N1 spec were different things, the Nismo cars had cosmetic mods only and were reasonably common in the earlier production years.  N1 spec was a different story and was different by year depending on Vspec 1 or Vspec 2 base, they also had cosmetic changes but also larger, steel wheel turbos and larger brakes (brembo) on vspec 2.

Still, these days everything is getting hard to find, so good score.

  • Like 1
2 hours ago, Duncan said:

Actually Nismo GTRs and N1 spec were different things, the Nismo cars had cosmetic mods only and were reasonably common in the earlier production years.  N1 spec was a different story and was different by year depending on Vspec 1 or Vspec 2 base, they also had cosmetic changes but also larger, steel wheel turbos and larger brakes (brembo) on vspec 2.

Still, these days everything is getting hard to find, so good score.

Yeah true, my bad. Still cheerin!

  • 1 month later...

 I always wondered how or if that could even be done, the rails look awesome. mine aren't awful but definitely bug like that. anyways cheers the whole build is very imformative.

could you just cut the dinted area out and have a piece fabbed up to fit in and work away at it until it looks flush and clean, instead of doing the whole rails? my cars in pretty good shape not ready to install a whole new rail lol from another car but would like to fix the dinted area up.arent as bad as your old ones

On 3/16/2020 at 9:02 AM, MoMnDadGTR said:

could you just cut the dinted area out and have a piece fabbed up to fit in and work away at it until it looks flush and clean, instead of doing the whole rails? my cars in pretty good shape not ready to install a whole new rail lol from another car but would like to fix the dinted area up.arent as bad as your old ones

You would probably be better off using a slide hammer and pulling the dint out. Most people do that, unfortunately mine were too far gone. 

you are the man! thanks for the advice. not to be a lazy azz im gunna research the slide hammer technique but any pointers or advice when I do this? do I heat the rail up when doing it etc.  im just trying to figure out  how I would connect the slide hammer to the rail and assume I am hammering straight south toward the ground...

I seen a couple smart guys on this site drilling a couple holes attaching the slide hammer that way. I think I just gotta be a man and get under there and get at it! seeing how you repaired it gives me insipiration to do a good job hopefully look stock again. I will continue following your build m8.

  • Like 1

You can get pullers that you spot weld on then pull down on but not sure if they would have enough leverage. Slide hammer you might need to drill a hole in the metal. Not too familiar with the methods sorry.

yeah mate worked like a charm. I only have done one so far out of the 4 but looks good. definitely not to caliber of yours but I can deal with it. thanks again I feel pretty happy I was able to do this. Thread gave me some confidence to try. see if I can get a pic for yeah shop is quite dark. I did end up having to weld it on and definitely had the tourque. once the rail was heated up proper it went easy.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
×
×
  • Create New...