Jump to content
SAU Community

Recommended Posts

Hey All

I can't seem to find this problem anywhere. After highway driving for 20 mins or so and leaving it in 5th I hear a slight whine from diff at 80kph. I have changed the diff oil to nulon 75w90 correct spec and it made absolutely no difference. 

Any idea what the problem is? And no vibration at all.

Some say additives work some say they don't but I don't want to fork out for the redline stuff for it not yo fix anything. 

Ideas pls?

Link to comment
https://www.sau.com.au/forums/topic/478849-r32-gtst-diff-whine-after-warmed-up/
Share on other sites

On 10/4/2019 at 11:10 PM, Dil-Dog said:

Time to weld it ?

Welding won't fix it, it will be due to pinion bearing wear and the pinion/ring gear mesh is slightly off causing it whine. 

Needs rebuild to fix, and depending on how long its been driven like this the pinion/ring gear might need to be relapped. 

-Blake.

  • Like 1

My $0.02.

In other words, crown wheel and pinion is rooted. Maybe not totally rooted but if it's making noises the damage has been done and they're on the way out. Need new MATCHED set, installed and shimmed correctly for correct gear backlash. There is no magic fix for worn diffs and no additive is going to fix it, no not even that Redline crap everyone raves about.

I stuffed mine that bad in one of my GTRs in the front (where people usually run lighter oil) that the crown wheel and pinion gears were actually razor sharp to the touch, which is a lot of wear if your familiar with crown and pinion gears. It made all sorts crazy noises under load, and why your noise is appearing once the diff oil is hot and thinner in your differential. I will never run ANYTHING other than 75w - 140 in any GTR diff front or rear again after that. After 19 years of GTR ownership anyone who runs stuff like 75w - 90 in any GTR diff front or rear is asking for trouble. I know it's a gtst but same thing basically. Anyone tells you to run 75w - 90 is a dickhead and asking for a diff rebuild, unless changed very regularly and / or has very little power.

It's all about protecting the crown wheel and pinion and the heavy stuff does the job, especially when most people don't drop their diff oil that often.

Motul comp gear 75w - 140 or Castrol Syntrax 80w - 140 (used to be SAF-XA) or you may as well put water in your diff.

Both the Castrol and Motul is generally around the $30 - $45 a litre range. Most other reputable oil companies have diff oil in that range too, Castrol and Motul just seem to be the top pick and Castrol is readily available. Castrol used to be the most recommended by companies like Holinger and Albins until the Motul stuff came along.

On 10/7/2019 at 11:46 AM, LINK17 said:

I think this is the problem, I checked the diff oil and it's 75w90, thanks for the great advice. 

I love the motul stuff but can't find where to buy except stupid prices online?

I use the Motul or Nismo oil. Its expensive but you don't need much and have you priced a diff rebuild?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...