Jump to content
SAU Community

Wheel Sizes & Offsets For Skylines

Sydneykid
 Share

Recommended Posts

  • Replies 3.8k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

whatsisname
whatsisname

Thank you to everyone within this thread that answered my questions and provided info, and ultimately helped me select my new wheels (width and offset) Here's the end result (minus big brake kit awa

N155@N
N155@N

Thought I'd share my setup since there doesn't seem to be much info/examples out there for this particular setup. Perfect for spirited driving on back/mountain roads, not so ideal for daily driving or

joeyjoejoejuniorshabadoo
joeyjoejoejuniorshabadoo

Posted Images

onthesuss Newbie

onthesuss

Posted
Posted (edited)

Hey guys,

been looking through this thread and other forums for ages trying to decide on a good wheel fitment for an r33 s2 gtst. Seems like 18x9 +20 would be a decent fit for an r33 all around flush fitment that wont foul suspension and can be cambered in to prevent scrubbing on guard liners. Have seen examples of this size in a set of work xd9s (dontyellpl0x) and a set of rota grids (boosted_andy). Would consider anything similar to 18x9.5+30 but it seems that at this wheel size its a bit hit and miss whether or not it will foul suspension/brakes. What wheels are still being made in 18x9+20 (grids and xd9s/d9rs not available in this size anymore) or 18x9.5+30 which dont foul brakes? Dont want to mess with spacers.Want to run 235/40 all around. All guards already rolled ,dont want to bin guard liner.

Cheers guys.

Edited by onthesuss
  • Like 1
joeyjoejoejuniorshabadoo Grand Master

joeyjoejoejuniorshabadoo

Posted
Posted

Hey guys,

been looking through this thread and other forums for ages trying to decide on a good wheel fitment for an r33 s2 gtst. Seems like 18x9 +20 would be a decent fit for an r33 all around flush fitment that wont foul suspension and can be cambered in to prevent scrubbing on guard liners. Have seen examples of this size in a set of work xd9s (dontyellpl0x) and a set of rota grids (boosted_andy). Would consider anything similar to 18x9.5+30 but it seems that at this wheel size its a bit hit and miss whether or not it will foul suspension/brakes. What wheels are still being made in 18x9+20 (grids and xd9s/d9rs not available in this size anymore) or 18x9.5+30 which dont foul brakes? Dont want to mess with spacers.Want to run 235/40 all around. All guards already rolled ,dont want to bin guard liner.

Cheers guys.

9.5+30 will fit.

Will the car be low? If so you are better to lip the front guards

KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

Hey guys,

been looking through this thread and other forums for ages trying to decide on a good wheel fitment for an r33 s2 gtst. Seems like 18x9 +20 would be a decent fit for an r33 all around flush fitment that wont foul suspension and can be cambered in to prevent scrubbing on guard liners. Have seen examples of this size in a set of work xd9s (dontyellpl0x) and a set of rota grids (boosted_andy). Would consider anything similar to 18x9.5+30 but it seems that at this wheel size its a bit hit and miss whether or not it will foul suspension/brakes. What wheels are still being made in 18x9+20 (grids and xd9s/d9rs not available in this size anymore) or 18x9.5+30 which dont foul brakes? Dont want to mess with spacers.Want to run 235/40 all around. All guards already rolled ,dont want to bin guard liner.

Cheers guys.

235 is too small for 9.5 and marginal for 9in.

viper2002 Rising Star

viper2002

Posted
Posted

Hi guys,

I'm looking to pickup a set of these wheels in 18x9 for my R34 GTT:

http://marsperformance.com.au/MARS-MP-37-4x-18-Inch-Matt-Bronze-Alloy-Wheels-Rims-5-x-1143

I don't believe the car is lowered and I would prefer to not roll the guards. These are the tyres I'm looking to fit:

https://www.tyresales.com.au/buy/tyre/kumho/ecsta_le_sport_ku39/235-40r18/1383?q=4

The offset available for the wheels is 15mm and 22mm.

What wheel sizes should I order in order to get a flush fit without having to roll the guards? Will the 235/40/R18 also fit properly?

Thanks

viper2002 Rising Star

viper2002

Posted
Posted

Update: I've been recommended 15mm on the back and 22mm on the front which is what this R34 is using (although on 225/40/R18 tyres):

http://imgur.com/y4rFwgt

What do you guys think? Will 235 be ok?

sleptema Proficient

sleptema

Posted
Posted

Update: I've been recommended 15mm on the back and 22mm on the front which is what this R34 is using (although on 225/40/R18 tyres):

http://imgur.com/y4rFwgt

What do you guys think? Will 235 be ok?

Yes, 235 will be fine.

If you are concerned about legality, I would go for the +22. The 15 will be a fairly aggressive fitment and assuming you are not lowering the car. I have 9.5+20, which is close to your 9+15, and my rims poke both front and back, even with camber.

viper2002 Rising Star

viper2002

Posted
Posted

Yes, 235 will be fine.

If you are concerned about legality, I would go for the +22. The 15 will be a fairly aggressive fitment and assuming you are not lowering the car. I have 9.5+20, which is close to your 9+15, and my rims poke both front and back, even with camber.

Thanks for that.

More concerned about aesthetics than legality to be honest... haha. I think the picture above might be 15mm at the back and 22mm at the front however, doesn't look like it pokes out too much?

sleptema Proficient

sleptema

Posted
Posted (edited)

Thanks for that.

More concerned about aesthetics than legality to be honest... haha. I think the picture above might be 15mm at the back and 22mm at the front however, doesn't look like it pokes out too much?

Depends on what angle you look on. Here is 9.5+20, with some camber. Don't get me wrong, I wouldn't change my offset for the world, I think it is perfect, but the cops wouldn't like it that's for sure. If you're only worried about form, go for it. You could run +15 all round if you wanted to. It's pokey, but not mexican.

post-80854-0-97030400-1454402160_thumb.jpg

post-80854-0-22244300-1454402192_thumb.jpg

Edited by sleptema
luke gtr Grand Master

luke gtr

Posted
Posted

I attempted to use search for this, but it came up empty.

I searched for a known size, still naught.

Don't think it likes numbers.

So........

Anyone know/ have pics of 18x10.5 +22 on a 32 gtr?

How close are we going to get to guards, suspension?

joeyjoejoejuniorshabadoo Grand Master

joeyjoejoejuniorshabadoo

Posted
Posted

Depends on what angle you look on. Here is 9.5+20, with some camber. Don't get me wrong, I wouldn't change my offset for the world, I think it is perfect, but the cops wouldn't like it that's for sure. If you're only worried about form, go for it. You could run +15 all round if you wanted to. It's pokey, but not mexican.

attachicon.gif20151013_121327.jpg

attachicon.gif20151013_121349.jpg

That front one is deceptive though. You can easily pull the front guards out enough to reduce the poke.

I had 9.5+12 up front with no flaring and less poke than that :)

  • Like 1
  • 2 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • oHBoy.
      2001 R34DE

      By oHBoy. · Posted

      3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
    • MBS206
      boost source Size Garrett gt28 gen2

      By MBS206 · Posted

      Why are you so adamant on going M12? Why not follow Brad (GTSBoy) suggestion. You're talking moving from a 1/8" size, to a 1/2" effectively. 4 times bigger. Why skip the commonly available sizes in between? The bigger you go, the more likely you are to strip the threads out at a later date, as guaranteed, someone will put a huge spanner on the M12 and really tighten it up, and you're only in thin wall, so not a lot of threads to engage!
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Hi. Yeah thanks. Car is already at tuners and it staying there to resolve "many" issues they do not like. So it is in a good hands. Getting a good tune on that Nistune ECU too so the car would be good. Just needs a little tune up and love.
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      Probably gonna remove manifold and turbo. I’m not sure if I can get M12 x 1.5 air tight. Could use high temp Loctite 246 or something similar, but I don’t know. Maybe it’s just best to remove everything again and weld an 1/8NPT on there instead.
    • cosline
      R32 gtr transmission strength, billet plate

      By cosline · Posted

      Yeah, saw the ratios, not impressed. Would like the punch I have in the first gears now. With those ratios it won't be the same.  Also want the h pattern gearing, or at least a quiet gear set that don't need to come apart for service each year. Looks like the only "reasonable" way Is a 8hp70 transmission, but where is the fun in that🤷‍♂️
×
×
  • Create New...