Jump to content
SAU Community

Recommended Posts

18x9.5 +20 is perfect for a RS4 auto..after that well... if you have kids and actually use your car for family dutys , its gets silly

with regards to camber for fitment and tyre wear imo..

cheers

darren

Waaay too much poke in the rear on an auto! Unless your going for the super stance poke/camber look

I have 18x9.5" +20 all round on my RS4S (manual) and with 235/40's stretched on the rim sits 4-5mm proud of the body front and rear with 1.5 neg camber front and .7 neg in the rear.

Also if you want to run this fitment on a manual stag with large bore Coilovers you will NEED fully adjustable camber arms in the rear.

i'm not into stance /whatever look..i just know any less than that looks gay as aids, looks like a magna or camry wagon ,and any more needs to much camber and low

to make it clear anything..and wear inner tyres and smash spoon drains/parking concrete blocks

i hardly call it superstance..lol

Edited by jet_r31

What size tyre you running? My manual (40mm narrower rear subframe, so 20mm less a side) running the same spec/fitment wheels you claim to have and mine sit out further than your pic? When yours should sit out 20mm further than mine? Odd

  • 3 weeks later...

Disagree, I have 19x9 +45 with 10mm spacers (effectively making them a +35 offset) on my RX. I reckon that 9" wide with a +30-35 is about perfect (but I am not into the stretched look) for an RS/RX. Maybe another 5-10mm for the ARX/Axis?

BC-19x945-10mmspacer1.jpg

BC-19x945-10mmspacer2.jpg

That looks great Cam. What size tyres are you running and how much clearance to the front strut do you have? Did you have to do any guard lipping/rolling?

I am looking at getting 20 x 9s very soon for my ARX. The wheels I am looking at come in +38, +32 and +20. I am leaning towards the +20 due to the flares, however, the +32 may allow me to fit slightly wider tyres so I have some rim protection. Although the flares on the ARX/AXIS sit out a little bit, as far as I understand the guards are essentially the same as the RS/RX just with holes in them. Ideally what I am after is the edge of the tyre sitting flush with the flare. If any ARX/AXIS owners have fitted 9 inch wheels, what offset did you go with and what tyre size did you fit?

Cheers

IMO 20s are not good for the ride of the car, and they don't handle well with the choice of tyres either. 18/19 is a far better option.

You'll never get a flush look with the Axis/ARX because of the large lip on the guards.

This is 19x8.5 +22 and 225/40/19 lowered on Nismo springs, but not very low. Not a rub or scrub on anything.

Sorry I don't have any down the side of the car pics handy.

6252549969_b5fee1b4ce.jpg

6232302952_54fefa719c.jpg

Thanks Alex for the advice and pictures. You actually told me your tyre sizes when we spoke at the Skyline Nats in Goulburn in September but by the time I got home I had forgotten it. Your car looks great by the way - but I guess you don't need people to tell you that. Shame Craig (Jetwreck) and Scotty's wagons weren't there, but it was good chatting to you and Craig.

The tyres I am looking at are either 245/40R20 or 275/35R20. This gets me closer to the original factory diameter than the current tyres I have on (235/50R18). One thing I have noticed is it appears the AR-X has larger rolling diameter wheels than the RS/RX. According to the handbook the 17 inch wheels wear 215/55 (668mm) and the 18 inch wheels wear 225/55 (705mm). I think the Axis is the same as RS/RX for rolling diameter. Could the larger diameter wheel on the AR-X be more forgiving to the larger 20" wheel?

I think the wheels I am looking at also come in 19 x 8.5 with either a +15 or +32 offset but I need to confirm this with the Australian distributer. Tyres to suit would be 245/45R19. I am still worried that after all the expense 19s won't feel the guards nicely - yes, I'll admit this is mostly about looks but at the same time I don't want to compromise comfort and handling.

I take your point about the large lip on the AR-X/Axis. So long as the wheels come out a bit further than standard I'll be happy even if it's not totally flush.

For anyone with an iPhone, TireLab and Rim Offset are two good apps for working out clearances. TireLab includes the tyre in its calculation.

That looks great Cam. What size tyres are you running and how much clearance to the front strut do you have? Did you have to do any guard lipping/rolling?

They are 245's. The wheels are +45's but rub on the upper arm when bolted up on the hub. Those pics are with 10mm spacers installed (still running them that way)

  • 1 month later...

I've read this thread a few times and just wanting to confirm that 17x9 +30 all round with either 15-20mm spacers for the front would fit a s1 c34 Auto? Car has 340/330mm height and rear camber+toe arms and front whiteline adjustable bushes if that effects anything? Also would i need to roll the rear guards at all? Thanks

Ok cool, thanks

What is the objections to running spacers? If u buy longer wheel hub bolts and do it properly is it still dangerous? Was thinking of running spacers for now as i have skyline rims and was thinking of running 8mm rear spacers with 60mm hub bolts and then 20mm hubcentric spacers (I think its called) up front? Also the rim is 8" front and 9" rears but Im running 235/45/17 all round so will this damage or affect my attessa, abs, or any other problems?

Ok cool, thanks

What is the objections to running spacers? If u buy longer wheel hub bolts and do it properly is it still dangerous? Was thinking of running spacers for now as i have skyline rims and was thinking of running 8mm rear spacers with 60mm hub bolts and then 20mm hubcentric spacers (I think its called) up front? Also the rim is 8" front and 9" rears but Im running 235/45/17 all round so will this damage or affect my attessa, abs, or any other problems?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
    • Wife and I are still looking for a new home. One condition was a large enough garage for a full-size lift in one bay. Now if only we could find something... We've been looking for almost a year now.
    • Thanks everyone for the ideas! Sadly, ramps are a no go for me. With young kids at home, I do most of my work late at night while they're sleeping. Starting the car multiple times wouldn't be a great idea.  I'll go see one of those new long reach low profile jacks and take a couple measurements to see if they will fit.   
×
×
  • Create New...