Jump to content
SAU Community

Recommended Posts

R34 GTR non V-Spec

Apexi Power FC

Apexi Air Filters

Greddy Profec B-Spec 2

Nismo Air Flow Meters

Nismo Radiator

HKS GT Intercooler

HKS 2530's

100mm Catback Exhaust

Impul Front Pipe

Sard 650cc(i think) Injectors

Sard Fuel Regulator

Walbro Intank Pump

Tomei Type B Poncams

Tomei Cam Wheels

Tomei Manifolds

Tomei Dumps

Tomei Fuel Rail

314kw atw on 18psi on first tune.

Hypertune intake manifold and single throttle body installed, retuned and now making 360kw at 18psi. Still stock bottom end :)

89 GTR

33gtr crank

standard rods and pistons

N1 water pump

N1 oil pump

x force dumps

unknown front pipe

apexi cat back

apexi pod intake

sard 650 injectors

040 pump

garret/hks 2530s

port matched inlet - exhaust

adjustable cam gear

pump and afms run out of puff at 265kw on 16psi, lots more to come soon.

post-34794-1211114515_thumb.jpg

Edited by robbieraver
  • 4 weeks later...

89 r32 gtr

apexi pfc+hc

hks split dump, bee-r front pipes, highflowed cat

trust 300+600+100mm cooler

greddy cam gears

hks pods

exedy heavy duty clutch+lightened flywheel

made 241awkw@7177RPM and max M.A.P OF 203.8KPA@7080RPM (TUNED AND DYNOED BY PROTEK AUTOMOTIVE ON BP ULTIMATE FUEL)

soon to go in are bosch z32 afms, nismo 600cc injectors, tomei 260deg 9.15mm lift cams, will get results and dyno sheet up asap

Edited by GTRBOS
  • 1 month later...

R34 GTR V Spec:

HKS front pipe

HKS cat back Hi Power system

HKS pods

Made 215.1 awkw @ 7000RPM 0.9 BAR Boost

IS Motor Racing Dyno

In a few weeks time, adding Nismo fuel pump and fuel pressure regulator, HKS EVC to bump the boost up to 1.2 Bar.

Will post up results of these when done.

Cheers

94 R32 GTR

Rebuilt standard turbos with steel exhaust wheels and 360deg thrust bearings

Nismo 600cc injectors

Nismo fuel Reg

Bosch 040 pump

Apexi PFC

Greddy Profec B II Boost controller

Adjustable cam gears

HKS Pods in custom air box

Trust front pipes

Hiflow cat

Trust Cat back exhaust

Engine internally standard

Standard items: Intercooler, manifolds, dumps, coils, afms.

Dyno: Dynopack 4 wheel hub dyno.

Result: 281 4wkw and 472nm @ 18psi

post-17186-1216379645_thumb.jpg

VEHICLE: 1989 GT-R

ENGINE: RB26DETT, 88mm bore, CR=8.7:1

MILEAGE: 127xxx Kms

OIL/WATER PUMP: Nismo/OEM

OILING SYSTEM: Tomei Orifice, Tomei pan baffle, Greddy oil cooler and filter relocation

INJECTORS: 600cc Nismo

FUEL SYSTEM: Bosche 044 in-tank

TURBO SETUP: twin GT2860R-5

MAP or MAF's: MAP

INTAKE SETUP: Apexi Power intake

INTERCOOLER: OEM

VALVETRAIN: JUN 264/264 9.7 mm lift - adjustable gears

HEAD WORK: Intake mildly ported and left rough, exhaust opened up about 15% and polished, combustion chamber polished

EXHAUST: HKS dumps, Tomei DP, 85 mm HKS Priest

BOOST LEVEL: 1.2 bar = 17 psi - Blitz Dual SBC Type R

ECU SETUP: ViPEC Speed Density

Nice conservative tune intended to let me have a ton of fun without making rebuilds my hobby.

HP: 390

TQ: 330

DynoLightspeed-2008Jul17.jpg

r32 gtr

v Spec 80k

Garret 2860r-5

trust dump pipe and nismo rear exhaust

nismo afm

power fc

nismo injectors and pump

otherwise standard

300kw and 730 Nm at the wheels

20 psi max boost with safe air fuel ratios

BNR32

Garrett 25/60r Turbos

Power FC

Sard 660cc injectors

Bosch 040 in tank fuel pump

Apexi air pods

(Standed turbo pipes and cat).

Low Boost 14psi made 268kw High Boost 18psi 297kw .

Edited by Rav

ported head matched manifolds

jun guilds stano vavles

stock cams

stock cam gears and springs

baffled sump oil restrictors in the block cam cover plates

jun collar and oil pump

acl race bears mains and big ends

rev rods

cp pistions

1.3mm metal head gaskit

metal inlet manifold gaskits

pfc

stock cooler

stock inj stock fuel pump

stock air flow meters

stock dump pipes

front pipes 3 inch cat 3inch exhuast and cannon

stock turbos

os giken twin plate clutch

eboost 2 set to 13psi

262rwkw!!! 351hp

i was very surprised! can not thank anth enough at turbotechics more responce every were! and better on fuel! :D

PHA71L

new pb of 12.046 181.23kmh 60 foot 1.701

post-42837-1217913553_thumb.jpg

  • 3 weeks later...
Gday,

Just got my car tuned after being off the road for about 3 years. Ive put an RB26 engine (and an R33 gearbox) in an R32 gtst. The tune is a preliminary one, so ive gotta run the car in and go back in about 1500kms so they can turn the boost up.

The car made 345 rear wheel kilowats on 17 psi and 98 octane. There should be more to come, but after driving it home from Silverwater in the wet, im not sure more power is a good idea in a rear wheel drive application!

The specs are as follows:

R33 RB26 (prepped block etc, compression is 9.0:1)

ARP head studs and rod bolts

General head reconditioning but no porting or polishing

Standard cams

HKS cam gears

CP Pistons 20 thou over

Prepped standard rods

N1 oil pump

Tomei sump baffle and head oil restrictor

R33 gtst 5 speed

Jim Berry modified Nismo 5 puck clutch

Autronic SM4 computer

Autronic boost control

Garrett GT35r turbo with 1.06 turbine housing HPC coated

Tial 44mm external wastegate with 17psi spring

Tial 50mm BOV

600x300x100mm intercooler

Earls 16 row oil cooler

Stainless manifold bought from GCG. Modified with extra support brackets and HPC'd

3.5inch dump, HPC'd and wrapped

3.5 inch custom exhaust thats really quiet.

Walbro in tank pump (255l/hr i think)

Surge tank with Bosch 044 in line (i also used the HICAS lines as fuel lines)

Sard 700cc injectors

Edelbrock fuel reg and modified standard fuel rail

Ford falcon twin thermo fans with 50mm alloy radiator.

I think thats it.

Just gotta get it engineered and registered now.

Shaun

Just to update, i got the final tune done yesterday and had the closed loop cruise initiated. The car made 350.5rwkw @ 17psi, but more importantly, i gained 76Nm of torque which is really noticable on the road. The old and new dyno sheets are below.

Im pretty happy with that,

Shaun.

post-11456-1219452439_thumb.jpg

post-11456-1219452561_thumb.jpg

post-11456-1219452849_thumb.jpg

post-11456-1219452997_thumb.jpg

Edited by Shaun

Engine

HKS step1 camshafts 264/272

HKS adjustable camgears

HKS inlet manifold gasket

Gates timing belt

cometic head gasket

custom P20 tool steel heat treated billet CNC machined oil pump

R33 RB26 crank shaft

external oil return lines from cylinder head to sump

Garrett GT35R Ball Bearing turbo (A/R 70 compressor housing with anti surge . A/R .78 Divided exhaust housing)

TiAL 44mm external wastegate

screamer pipe

custom steampipe Manifold to suit divided turbine exhaust housing

custom dump pipe + front pipe

hi flow 3inch cat

X force cat back exhaust system

115mm intercooler

custom aluminum intercooler piping

custom intake pipe

custom air box

greddy blow of valve

custom catch can

aluminium radiator

dyno2.jpg

dyno1.jpg

VEHICLE: 1990 GT-R

ENGINE: RB26DETT

OIL PUMP: N1

INJECTORS: Standard

FUEL SYSTEM: Walbro 500HP

TURBO SETUP: twin GT2860R-7

MAP or AFM's: Standard AFM's and MAP

INTAKE SETUP: Apexi Power intake

INTERCOOLER: OEM

EXHAUST: GCG dumps, Veilside 3.5" exhuast and front pipes

BOOST LEVEL: 1.2 bar = 17 psi - G-Reddy Profec B Spec II

ECU: ViPEC V66

n905000300_3968353_6895.jpg

  • 3 weeks later...

VEHICLE: 1991 GT-R

ENGINE: RB26DETT

MILEAGE: 3780 Kms

CHASSIS MILEAGE: 78xxx.xx

OIL PUMP: N1

WATER PUMP: N1

OILING SYSTEM: Tomei pan baffle, Greddy oil cooler and filter relocation

INJECTORS: 550cc Nismo

FUEL SYSTEM: Standard R32 GTR pump

TURBO SETUP: twin Trust T517z

MAP or MAF's: Nismo AFM

INTAKE SETUP: Standard - Apexi foam filter

INTERCOOLER: Trust/Greedy 300+600+100mm cooler

VALVETRAIN: Standard camshafts - Old Skool HKS adjustable gears

HEAD WORK: Mild port n polish to just linish any burrs only.

BLOCK WORK: Cryoed and preped block, HKS 2.6 Billet crank, Trust/Carrillo Conrods, Weisco Forged pistons

MISC ENGINE PARTS: ACL race bearing, mains and big ends, Tomei headgasket, Racepace Radiator

EXHAUST: HKS front pipe, Racepace manifold, 90 mm HKS Dragger

BOOST LEVEL: 20 psi

ECU SETUP: Apexi PFC

320.1kw @ RACEPACE

1996 R33 GTR Vspec

Tomei 260 Poncams

Tomei cam gears

Splitfire DI coilpacks

Sard 700cc injectors

Sard Fuel reg

reco'd stock fuel rail

Apexi PFC

Greddy Profec E-01 EBC

Bosch 044 fuel pump

Greddy front pipes

High flow cat

Greddy 3" power extreme II exhaust

Grex oil filter relocator kit with remote oil cooler

100mm FMIC

KKR hard piping kit

Stock air box with K&N panel filter

Stock turbo's

Stock dumps

Stock engine internals

OS Giken twin plate STR clutch

Stainless Oil sep/water bottle system

post-16592-1222562050_thumb.jpg

As you can see, plenty of old fashioned dyno shake which hampered performance slightly.

235 awkw @ 15psi with a projected output of 280rwkw with the front driveshaft disengaged.

This is a peak torgue tune from ADVAN Performance specifically for track/street with the 15psi boost threshold being reached at 2800rpm.

post-16592-1222562222_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Cheers. Skyline is back on the menu, can’t get rid of it. It’s like a child you don’t want, or herpes 
    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
×
×
  • Create New...