Jump to content
SAU Community

Recommended Posts

im sorry but did we go over how to seperate the side-blinkers also? i have the clear ones and ofcourse i want those to match black also...

do i do it the same way... with heat and such?

im sorry but did we go over how to seperate the side-blinkers also? i have the clear ones and ofcourse i want those to match black also...

do i do it the same way... with heat and such?

What i want to know is how the hell can they charge $450 for a set of full clear R32 blinkers

like them=

post-14512-1155446179.jpg

And i know their is a place somewere hidden in japan that can make th full clear plastics for the winkers, EVEN the orange curb marker built into the winker plastic!

like this-=

post-14512-1155446018.jpg

The only question is WHO makes them!!!! then we can all change them over to CLEAR with no gay little orange curb light,

:thumbsup:

anybody seen the headlights on yahoo auction japan. the ones that are all mesh with a small round light in the corner... ill try to find a pic... found it..

bl2451-img500x375-1155803770r32_2.jpg

bl2451-img500x462-1155803765r32_1.jpg

guess i should ask does anybody have them, and have a better pic?

Do you think it will be good if we only replace the stock projector with an hid projector?

So i will keep the stock h3c bowl and put an hid cutoff shield with an hid projector.

Then, buying an hid h3c bulb kit.

is that a good? i'm just thinking that it will be easier, but i'm not sure how the h3c hid kit will light up.

  • 2 weeks later...
  • 2 weeks later...

i'm doing the same retrofit, but i'm using the e46 projector.

i have the same problem as you, the projector are smaller in lenght. So i will have to cut the back, in order to fit the ballast adapter wire to the bulb.

i got my over cooked ones out, and fitted a fresh set of headlights, and decked them out with blue angel eyes,! looks nice i think!

If anyone wants to get a set of angel eyes, be sure not to get squid rings, or LED eyes... they suck

They cost me about $170 and 2hours of fitting! but look trick!

post-14512-1158749915.jpg

i started my retrofit using E46 projector. They are very similar to the honda euro.

here are some pics.

e46 projector

IMG_1496.jpg

e46 projector with the bracket

IMG_1498.jpg

IMG_1499.jpg

IMG_1500.jpg

fitted inside the headlight

IMG_1497.jpg

IMG_1492.jpg

Back of the headlight.

IMG_1495.jpg

IMG_1493.jpg

now i will have to screw the projector to the bracket and use soem jb weld.

Then cut the back of the headlight, so i can fit the bulb adapter

i got my over cooked ones out, and fitted a fresh set of headlights, and decked them out with blue angel eyes,! looks nice i think!

If anyone wants to get a set of angel eyes, be sure not to get squid rings, or LED eyes... they suck

They cost me about $170 and 2hours of fitting! but look trick!

I am looking to get some, where did you get em from and can you get like other colours??

Sir D, I totally agree with you on that one. for some reason, nissan feels that the reflectors are better than projectors. For halogen lighting, they might very well be right.

All the r32s/s14/s13 with the projectors have absolutely shit light output. The r33 reflectors actually have pretty good light output compared to the r32 ones.

PS: My gtr lights are almost here. woohhooo. then comes the hardbit - trying to fit them. I might have an excuse to get gtr front bar, bonnet and possibly even guards just to fit these lights on.

lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
×
×
  • Create New...