Jump to content
SAU Community

Dose Pipe Sutututu

Members
  • Posts

    15,517
  • Joined

  • Last visited

  • Days Won

    371
  • Feedback

    100%

Everything posted by Dose Pipe Sutututu

  1. Ramp rates way too quick
  2. Maybe on paper it says it's a kit car? So car came in all bits and pieces and they legoed the shit out of it and now bares Honda plates?
  3. What kind of bullshit dyno run is that? Couldn't even turn up the volume and the run was over.
  4. done match? so you've done the matching I believe you mean don't match.. both very different words with different meanings. Because it'a R33, I would suggest investigating on a R33 GTS-t loom and swap the injector pins to suit. Then splice the sensor wires into the R32 sensors. Of course a RB20DET doesn't have VCT so you can just terminate those wires. Not really rocket science, you'll work it out.
  5. Also Ecu pin out is different you need to swap two injectors pins around. Look it up, I'm too lazy to do it for you.
  6. It's fine where it is, spend you time and energy on a dose pipe
  7. because I like dim sims, I will accept 80x Dim Sims from Din Tai Fung. This needs to include a mixture of: xiao long bao siu mai har gow
  8. minimum I will take: 2.5x slabs of Pure blonde 2.5x slabs of Asahi 2x slabs of Fat Yak 2x slabs of James Squire 150 Lashes 1.5x slabs of Asahi Black 24 bottles of Knappstein Lager 24 bottles of Rogers by Little Creatures Negotiable for 1L Grey Goose + 4x bottles of Knappstein.
  9. I reckon 10~15 years too late... most of our beloved R32/33/34 S13/14/15 are quite frankly overpriced cars. All these pricks have already gotten rich in the past and now just surviving living off what they do best.
  10. Project MU aren't that noisy.. if.. shims are clean shims have that anti squeal shit rotors are perfectly flat I recently installed 350Z Brembos, they don't come with shims OEM.. can't wait to drive on them.. will be squeal city. Lucky Project MU sell the shim kit for 350Z and R34 Brembos.
  11. Say if it's consistently low across 6 cylinders, all you need to do is consistently run more boost to make up for it. Simples
  12. The valve is never fully shut, also doesn't matter where it sits. Less exhaust flow means less noise.
  13. Ohhh naice no more pull out front shaft lol
  14. Powertune Unigroup has a 2WD dyno unless you're willing to pull out the front shaft or raise the front on jack stands (highly not recommended).
  15. Check if current one is dead, if you know how to use a multimeter see if the voltage fluctuates between 0.1 to 1 volt. If so sensor is ok
  16. Sounds like the FCCM or fuel resistor pack is dead. Just ground off your fuel pump, it's better for aftermarket ones anyway
  17. Serious note, unplug the O2 sensor, it should stabilise. If it does time for a new one.
  18. my rust bucket shit box came from Edward Lees.. well the previous owner bought it from Edward Lees LOL probably has 360xxx on the clock by now.. shows 160 xxx hahahah
  19. I vote for twin slash cut screamers out of the LHS quarter panel OR straight out of the bonnet.
  20. ^ no no no.. only the idle cells, it's just a way to determine the dead time at x voltage. So what you do, set the VE to 80 for cells around idle 0 to 50kPA and 0 to 900 rpm. Start car, monitor the voltage then adjust the dead time till you hit stoich. Of course all other VE cells will need to be adjusted to suit as the base map isn't really ideal.
×
×
  • Create New...