Jump to content
SAU Community

Recommended Posts

Alright it's not a GT-R but for a laugh...

SR20DET

Forged bottom end, cams etc. Still a 2 litre, ID2000's 3 x 044's

Precision billet 6265 turbo

It has 20psi @ 4500rpm

486kW at the rear wheels @ 39psi on E85

Ran 9.6 @ 144.6 on radials with 453kW so keen to hit the track again

No nitrous

Alright it's not a GT-R but for a laugh...

SR20DET

Forged bottom end, cams etc. Still a 2 litre, ID2000's 3 x 044's

Precision billet 6265 turbo

It has 20psi @ 4500rpm

486kW at the rear wheels @ 39psi on E85

Ran 9.6 @ 144.6 on radials with 453kW so keen to hit the track again

No nitrous

I call shotgun PJ. U know ur allowed passengers now at WSID. We might have to lie to them about u running slower than a 11.9 ;)

just like u used to keep sneaking in and running under 10.9s

+1 for the 400kw+ club

680 4whp ( on a hub dyno ??? ) what ever that is ? don't want to start a dyno war, but I'm sure its over 400wkw

HKS step2 2.8 stroker, full counter crank and rods kit, CP pistons.

Garrett TO4Z .84 rear

, Jun 272 in and ex cams, 10.8mm(?) lift, special retainers and all the jazz needed to support the cams and high revs, heads extensively ported.

Current street setup with wastegate plumbed back into HKS 4inch exhaust

1000cc HKS injectors,

Motec M800 ECU

+1 for the 400kw+ club

680 4whp ( on a hub dyno ??? ) what ever that is ? don't want to start a dyno war, but I'm sure its over 400wkw

HKS step2 2.8 stroker, full counter crank and rods kit, CP pistons.

Garrett TO4Z .84 rear

, Jun 272 in and ex cams, 10.8mm(?) lift, special retainers and all the jazz needed to support the cams and high revs, heads extensively ported.

Current street setup with wastegate plumbed back into HKS 4inch exhaust

1000cc HKS injectors,

Motec M800 ECU

507awkw

there was some talk of lumpy cams earlier in this thread, this is the idle of the above set-up jun272's

I fell in love with it..

its amazing how much poppier big cams sound in a 2.6ltr - the 3ltr muffles most of that sound

Also did you actually port the manifolds or extrude hone?

I'd like to get mine extrude honed to see how much difference there is

we spoke about this before stevo - i wanted to have mine done but not after the quote i got for over $1000

there was some talk of lumpy cams earlier in this thread, this is the idle of the above set-up jun272's

I fell in love with it..

ive got bigger cams than that and people reckon it sounds like a rotor at idle. Even a rotor workshop owner told me lol. Ill post a sound vid when its actually running again.

in 2021 :D

its very close to being ready to go, just need to wire up the new ecu setup (only recieved that today) now and the car loom, done a few changes and its actually in a bloody gtr. Engines been sitting on a stand for over 2 years now while building the car up. I might paint it green too ;)

its amazing how much poppier big cams sound in a 2.6ltr - the 3ltr muffles most of that sound

Bullshit!

Dan pulled up at the servo and some dude asked if we had a 13B in it. Coulda been blood if I was there. :blush:

F#@king hell Noel! I knew you had a nice GTST but that is insane. Top stuff!

What cams do you have?

Running tomei 10.25 lift with 270 degree inlet and 260 degree exhaust Dave. Going in tomozz for our first e85 tune, should be interesting.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Initially I thought having a pair of Recaro seats would be a big bonus, it turns out these do get a little uncomfortable on long journeys (my fault, not the seat). I had a look through the GSM Performance website at reclining seats and booked an appointment to visit their show room. I got the Recaro Sportster CS for the R34 from here, was very happy with the service received so of course a re-visit was in order. Unfortunately the two Corbeau seats I had chosen aren't on display but they had 4 other options available. Two seats dug into my back, one dug into my legs and the other was perfect. I also found out that Recaro seats use a larger bolt pattern so some adaption was required. Luckily GSM offer some universal adaptors that should solve this problem. I searched the interwebs for price comparisons and Corbeau themselves were the cheapest at £300 cheaper (for the pair). I asked GSM if they could price match, unfortunately they couldn't. I later received an email saying Corbeau would honour them the same discount, but the purchase was already made. I did however order the brackets from GSM, both arrived on the same day. I started with the passenger side seat, knowing this was going to be a little trial and error. There are 3 mounting holes at the front and 2 at the rear on these JURAN Racing seat rails.  With the adaptor brackets mounted, the allen cap bolts started to push into the seat, NOT GOOD!  The rear mounting holes lined up but there were issues at the front. The holes were 1/2 hole out, so the brackets got a tickle with the drill to modify the holes. The supplied bolts weren't going to be long enough and a spacer was needed to stop the adaptor bars from bending. A local fasteners company supplied be with some nylon spacers and longer bolts (M8x30, although these will be replaced with 35mm long shortly) A before and after I pre-drilled the front bracket before making a start on the driver's seat to save some time. And in no time at all that was in the car too. The all black seats have transformed the interior and these are MUCH more comfortable. The only downside with the new Corbeau seats is I sit a little higher, but I'll happily accept that over discomfort. The Youtube video can be found here: https://www.youtube.com/watch?v=wPyttKPktXA
    • All 3 I guess. The car came with the JASI Aero 4 door Type R Full Kit unpainted so this was one thing at the top of my list to complete then I noticed there were body panels parts for this kit so i picked them up along with some black mesh to fill in the front bumper and front side air vents. car is at a paint and body shop atm completing this work. Next I will be addressing the internal bells and whistles, great summer project I can do with the kids.  full interior removal - ,boys car sound deadening - pads and spray ,boys stereo, sound, lighting - Big 3, GTT or bigger alternator ,kids head lining - dye black add star lighting mod ,daughter. That's it for the next 5-6 months. I have some motor maintenance  work i have to plan out. oil filter relocation, gaskets, mounts. beyond that, mind is starting to turn over if i can use a DET intake plenum, block off turbo ports & pipe in a air intake.      
    • roller coaster of a ride. Alarm system was removed & main harness was repaired where possible. still no fix just random successful starts. moved on to the replacing the ignition switch and relay. well all this troubleshooting & repair has been going on, the car is at a paint and body shop being pushed around. Ive been going down there on odd days after work to get it sorted.     
    • 5th November if you want to come out for a spin wakfield
    • PROBLEM WAS BROKEN COOLANT SENSOR!!! Replaced with a new one and its running mint.
×
×
  • Create New...