Jump to content
SAU Community

Recommended Posts

little dip in power/response at 2700rpm - whats that about?

me screwing around :P (not really) i backed off for a second, thought i heard something :)

Just had a big day tuning at status. This is the first run with my new forged engine. Every thing on this engine apart from pistons are stock standard, so any good healthy RB25det will be able to do the same.

Just recap of modifications list:

800cc injectors

Nistune ECU

Z32 AFM

600x300x75mm FMIC

3inch turbo back exhaust

3inch intake pipe with pod.

CP pistons

ATR43G3 / Pu high flow .82

Stock engine head

Stock cams

Stock cam gears

Stock exhaust manifold

Stock inlet manifold

Stock fuel rail

Stock engine block, Con rod & Crank.

This is a controlled run based on BP 98 Fuel, No boost controller, No wastegate controller.

Car made peek of 303rwkws at 20psi with drop to 17psi (can be set with Gate controller). The constant was between 295 to 300rwkws.

atr43g3303rwkw.jpg

atr43g3303rwkwboost.jpg

Video of above run is up for people whom's interested to watch:

^^^

This is seriously good result man. Congratulations to both you and Trent. I've compared it with few GT3076R with .82 rears. The ATR43G3's got similar down low with like 50kw+ more mid rang and 65Mn more torque . Plus those 2x cars had heaps more mods and work done compare to yours. I've overlaid all 3 graphs.

post-31034-1283621759_thumb.jpg

^^^

Thanks for the graph, how ever above results does not represent the actual aspect of any of the cars in it as none of them runs identical modifications or run on the same dyno.

I guess some of your have already seen the result of our PU high flowed R33 turbocharger. I took few photos when its installed, and tuning video is now up:

puinstall1.jpg

puinstall2.jpg

Video of 3 dyno runs:

Final result:

puhf305rwkw.jpg

puhf305rwkwboost.jpg

This is seriously good result man. Congratulations to both you and Trent. I've compared it with few GT3076R with .82 rears. The ATR43G3's got similar down low with like 50kw+ more mid rang and 65Mn more torque . Plus those 2x cars had heaps more mods and work done compare to yours. I've overlaid all 3 graphs.

Umm I'm the owner of one of the cars, my GT3076R setup has LESS mods than he has (completely stock high km RB25, and had iffy coils which you can see evidence of in the midrange), running less boost, and my car has between 5 and 40kw @ wheels more than him up until he reaches his full boost which is over 4psi (21.6psi!!) higher than my PEAK boost in the whole of my run.

The massive torque difference is due to me not going over 17psi - the only reason our power curves are comparable is that despite me running a fair bit less boost my car makes comparable power. If anything I reckon it makes the GT3076R look comparatively really good. If you want to compare my GT3076R with that turbo, overlay the 17/18psi graph that Hypergear posted above as its only peaking at about 1psi more boost than mine was running - instead of 4... still gives him an advantage but it should give much more of a fair impression of an internally gated .82 GT3076R vs a .82 ATR43G3.

I'll be running my car on a dynapack next month now I've got new coils in it, it certainly feels a lot healthier through the midrange.

I have a different view, On the same time mine isn't holding boost either. But I'm not saying No. to the slight boost pike.

2ndly my job is building turbos, I know the type of wheel that you are using. My wheel has larger air gaps in between fins, That 50kws increase "could be" from that while yours is slightly out of puff.

The latest run is a stockie high flow not a ATR43G3. Even so it still made more torque and power, plus I still have the option of using BB cores.

Also my engine's not even run in during that tune. I had compression all over the places with run in oil.

But either way, like I said your sheet is the most impressive I've seen in the stuck of people who's running this turbo with better response and power then lot of people who's got / without more mods then you do.

Also I know people with dynos that reads heaps more then others. So I only use Status and Dr.drift's dyno. They are creditable tuners and their reading is within 2KWs difference. I can guarantee you mine is accurate, wither your dyno is happier I do not know.

So unless your car is on Status dyno there is really isn't much of meaning in this comparison.

And in your list of mods:

1997 R33 GTS25t

Unopened RB25DET, 165,000kms

BP Ultimate 98 Fuel

Nismo 555cc injectors

Walbro 255lb/hr fuel pumpfgvbbbb

GTSLink Plugin ECU

Apexi AVC-R boost controller with Norgren pressure relief valve aiding spool

Cheap random 600x300x76mm front mount intercooler

K&N filter with 4" intake

Garrett GT3076R .82a/r Internally gated turbo

Trust Power Extreme 2 exhaust

Your EBC setup will make noticeable difference in response.

Umm I'm the owner of one of the cars, my GT3076R setup has LESS mods than he has (completely stock high km RB25, and had iffy coils which .......

Mate have a read in the RB25det dyno thread. Compare to people with GT3076 .82s the ATR43 is a clear winner. I only picked your best run because it is the most impressive with 98 fuel. There is a fat difference from 4000 to 7000. How's your tinny bit difference pre 4000 helps when the paddle is to the metal.

No offence just Just my 2Cents

Edited by kwickr33

Stao I guess you don't pay much attention to other people's topics. "Lithium" 's topic in making his turbo spool faster is around for a while. You can find your answer there:

http://www.skylinesaustralia.com/forums/Gt....html&st=60

By the way my R34 high flow works great. I will be tuning it next week and post some results.

ReliefValve.jpg

That is a pretty interesting part. The dyno reading seems to be pretty ordinary with out it. Certainly made a very big difference in response.

post-31034-1284210136_thumb.jpg

Also means without it the Comparison looks like:

post-31034-1284210282_thumb.jpg

Edited by kwickr33
Stao I guess you don't pay much attention to other people's topics. "Lithium" 's topic in making his turbo spool faster is around for a while. You can find your answer there:

http://www.skylinesaustralia.com/forums/Gt....html&st=60

By the way my R34 high flow works great. I will be tuning it next week and post some results.

Thanks for the info. Its a very helpful thread to read. I'm definitely buying one of those things to test it out.

Mate have a read in the RB25det dyno thread. Compare to people with GT3076 .82s the ATR43 is a clear winner. I only picked your best run because it is the most impressive with 98 fuel. There is a fat difference from 4000 to 7000. How's your tinny bit difference pre 4000 helps when the paddle is to the metal.

No offence just Just my 2Cents

You are comparing Dyno Dynamics readings with a Dynapack reading - it can't really be done. The extra bit of spool before 4000rpm is just one of the things the GT30R does better. If I wasn't on stock internals I'd go and retune mine on a Dynapack for 21psi to overlay with the Hypergear turbo.... that'd be quite telling I suspect.

I believe the post he's referring to is your best run with dyno pack dyno. Thats before every one's reading about your tricks in getting better response. I'll certainly be trying that out.

In that run I did not use a EBC or a MBC. My boost isn't holding. It only spiked 21psi for a brief moment. I'll make it hold 21psi with gate controller, hopefully be picking up another 15kws up top.

I've strictly built the test engine in factory specifications. Means any healthy RB25det will have no issues doing the same.

Also Trent's Hub dyno reads within 2KWs difference to any roller dynos I've know. Also I've done 298rwkws with same turbo at Dr drift's roller dyno with a stuffed engine. You can check video footages of that run in page 45.

As far as dyno concern Status dyno does not read any happier then a accurate roller dyno. Every one who've used status can certainly confirm that.

How ever I'm still testing out few other combination improving response and top end, so stay tuned.

Will be good to see how it goes. The Dynapack I used is also not set to be a "happy" dyno - it has broken the odd heart around the place but IMHO I'd say a typical DD reading dyno would still drop both my and your power figure a little unless the Dynapack has been somehow calibrated to reduce its reading.

The problem I have with building boost at 100% until you get near your desired boost pressure (by the way of a boost controller) is traction, it makes it a whole lot harder to get traction on anything but slicks. I suppose maybe 4th gear it would be better.

Edited by Harey

Correct me if I am wrong but is lithiums car not SELF TUNED? Sorry what do you do for a job lithium? And Stao who tuned your car?

Righto.

Now, I spent 6 months straight crunching numbers and reviewing peoples results across a board of forums, and a well tuned RB25 with a 3076 should achieve close to the 200rwkw mark by roughly 4000RPM. I am talking about an internally standard motor, no cams.

From what I can see, your both off by some 80rwkw.

Lithium, I do not mean to take anything from your efforts. Your work continues to impress.

Stao, you are an excellent turbo builder, however this comparison is (for lack of more direct wording) flawed.

Now, I spent 6 months straight crunching numbers and reviewing peoples results across a board of forums, and a well tuned RB25 with a 3076 should achieve close to the 200rwkw mark by roughly 4000RPM. I am talking about an internally standard motor, no cams.

I can't find any that come even close to 200rwkw at 4000rpm... Care to point me in the right direction?!?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...