Jump to content
SAU Community

Recommended Posts

Yes, I'm currently making about 260rwkw. Thing is with sending off my turbo for Stao to modify, I live in Perth... So that's a huge down time for my daily confused.gif

I've got the G2, .64 housing. It's still just as quick, it still scares the pants off any mates that get in my car. It's just that I'm used to it now, 350rwhp got old quicker than I expected :(

No E85 in Perth, not at the pump anyway. I know forging won't give more power haha, I meant that when I can afford it I might forge and go for 500+.

Get a bigger rear, or get water meth injection and give it more boost and more timing!

Yes, I'm currently making about 260rwkw. Thing is with sending off my turbo for Stao to modify, I live in Perth... So that's a huge down time for my daily confused.gif

I've got the G2, .64 housing. It's still just as quick, it still scares the pants off any mates that get in my car. It's just that I'm used to it now, 350rwhp got old quicker than I expected :(

No E85 in Perth, not at the pump anyway. I know forging won't give more power haha, I meant that when I can afford it I might forge and go for 500+.

Get a bigger rear, or get water meth injection and give it more boost and more timing!

If you are bored with the power take the car off the road for 2 months, it will be even faster than than when you first put the turbo on.

My car was off the road for 5 months, when I got it going again f**k me dead it was amazing, the handling was the first thing I really noticed but the power was scary after driving a 1.3L barina for all that time.

So the SS1PU makes 260-280kw depending on boost on the status dyno but I cant find any results on any other dynos or from actual customer cars.

I have ordered an SS1PU and im a little worried that it will not perform as reported. The only result I see in Sydney is from Sarge and thats for an SS2 with some setup related complications.

Can anyone share their SS1PU results on a dyno other than from status?

Dont have a dyno printout yet but 232rwkw on 14-15psi before coils started to breakdown.

(this will give you some idea of potential of the PU)

when new coils & plugs inserted will get retune to fix boost up to 19-20psi and will post up dyno

Regards,

Dazza

Edited by itshimdazza

Dont have a dyno printout yet but 232rwkw on 14-15psi before coils started to breakdown.

(this will give you some idea of potential of the PU)

when new coils & plugs inserted will get retune to fix boost up to 19-20psi and will post up dyno

Before going for the next tune, Please drive pass and swap for a 20psi actuator once you have the coil packs fixed.

I'm waiting for Stao to finish up on my SSv2, hopefully it should be through to me late next week. Install and tune should be done the following week, I'll post graphs as soon as I have them.

I'm running:

Blitz return flow

Trust PE II

3" dump + front pipes

Walbro 255lph direct wired

HKS pod + z32

4" Hard metal intake pipe

Bosch 1000cc's

MV Automatics Stage 2 kit - valve body + welsh plugs

Will probably end up needing new plugs and coilpack

Thanks mate,

Was this with the latest SS1PU or another model?

Dont have a dyno printout yet but 232rwkw on 14-15psi before coils started to breakdown.

(this will give you some idea of potential of the PU)

when new coils & plugs inserted will get retune to fix boost up to 19-20psi and will post up dyno

Regards,

Dazza

Status/Chequered dyno is about as accurate as you'll get. Conservative ramp rates and up-to-date correction methods means it will be very similar to DD results etc. I know that within melb, there's less than 5rwkw diff between the major DD shops and Trent's dyno.

So the numbers are very accurate.

I FEEL THAT THIS RESPONSE REQUIRES CAPITALS SO HERE GOES.

STAO/HYPERGEAR YOU HAVE SOME F**KING EXPLAINING TO DO

JUST GOT MY CAR DYNO TUNED - 306HP ON 14 PSI :@:@:@:@:@:@:@:@:@:@

MODS - ATR43 SS-1, JJR 3" BELL MOUTH DUMP, SINGLE CELL CAT, HKS HI POWER CAT BACK, JJR TURN FLOW INTERCOOLER, SPLITFIRE COIL PACKS, K&N PANEL FILTER, 3" STEEL INTAKE PIPE, TURBOSMART TYPE 3 PLUMB BACK BLOW OFF VALVE, WALBRO GSS-342, TURBOSMART BOOST T.

NO MATTER WHAT THE TUNER DID WITH THE BOOST CONTROL IT WOULD SPIKE TO 20 PSI THEN HOLD 14 PSI TO RED LINE.

TURBOSMART BOOST T.

Get rid of this piece of shit and it will not spike. They should be called turboSPIKE boost t. I've never seen one work properly, even on the lowest setting with 5cm of hosing they caused spiking on my turbo.

Also lose the attitude you sound like a spoilt kid with that post.

Edited by Rolls

I dont know how its Stao's fault. lol.

If it spiked at the top end it would be a different story. Perhaps you should sort out your boost control issues before defaming a business.

Get rid of this piece of shit and it will not spike. They should be called turboSPIKE boost t. I've never seen one work properly, even on the lowest setting with 5cm of hosing they caused spiking on my turbo.

Also lose the attitude you sound like a spoilt kid with that post.

All of this. Especially the last part.

However I remember what it was like when I didn't make the power, I blamed Hypergear straight away too. Get rid of your craptastic boost controller and see how things go. 306hp @14psi isn't bad, these turbos only really come alive with higher boost. I'm sure you will see the power. don't start going off at Stao though, the man is legendary in going out of his way to help you.

I will blame him. The turbo has a 19psi actuator on it that he recommended and we only put the boost control on to try to keep the boost up. Without a boost control it does exactly the same thing. That power figure was without the boost t. From the day I received the turbo I told him it wouldnt work and he has repeatedly said no it's fine. Obviously it is not fine. If it was a boost control issue do you think I would be ranting about him.

Edited by lilcrash

Either a boost leak or exhaust leak would cause a boost drop that dramatic.

Can you pressure test the intake system and confirm you have no broken exhaust studs etc?

From the day I received the turbo I told him it wouldnt work and he has repeatedly said no it's fine.

The turbo probably is fine and it is a set up related issue.

Edited by Rolls

Get rid of this piece of shit and it will not spike. They should be called turboSPIKE boost t. I've never seen one work properly, even on the lowest setting with 5cm of hosing they caused spiking on my turbo.

There was one on my Soarer when I got it, spiked to >20psi at 1/4 throttle, first thing I did before driving back to canberra was rip it off.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Put a fuel pressure gauge on it. Replace the turbos. Probably completely separate issues.
    • What copper washer do you guys use on the bleeder bolts? The existing one I have I had no idea where to find it in a local store, I did buy some online but that are only 1mm thick whereas my old one is 2mm+ thick and when I put the new washer out and squeeze the top radiator hose I can hear a bit of air but not with the old one. Does this matter? The new one doesn't leak, but the inner diameter is a bit loose whereas the old one threads on the bolt.
    • Howdy all, after being out a few weeks ago on a spirited drive in my GTR I have 2 issues that oddly have appeared at the same time. Whilst accelerating quickly through the gears all of a sudden i’ve lost power at the top of third gear (below redline around 6000rpm) for no obvious reason.    From that point onwards the car has been running rich on idle, won’t really rev under load without a ton of black smoke and the odd backfire, and dying as a pull up to a set of lights unless I keep the revs up around 1500rpm. In addition when shutting down the car that same night (I was 10 minutes from home) I noticed one of the turbos was significantly noisy on wind down when shutting off the engine. After letting the car cool down overnight it starts up fine, although once it gets to temp the revs start to creep up and down, the exhaust is darker than it should be and it also sounds like it’s running rich (fat note) I’ve put a new set of plugs in it - no change, the old plugs all seemed OK with two of them being somewhat richer/fueled up than the other 3 with 1 being borderline. I’ve smoked tested the intake system via the front of the Turbos, found a split vacuum hose going to the factory boost gauge sender, which I have since replaced.  Also found another leak on the gasket coming off the rear turbo outlet, have also replaced this. After fixing both of these leaks - still have the running rich issue. I’ve also tried another pair of AFM’s - no change here After pulling off the front turbo intake pipes, there is obvious shaft play in the front turbo, which now hisses loudly on light revvs although I can’t see why this would make the car run funny even under idle. I’m curious to know why it’s running rich before I potentially replace/rebuild turbos. The car is completely stock <50,000kms  other than an exhaust. Oil and coolant are all clear. I haven’t bothered with coil packs as it looks like they won’t be the issue due to condition of the plugs. Any help appreciated as I cry myself to sleep!
    • No probs at all. I used to love trying to dig up obscure info for those in need where possible going back 20+ years on SAU.  I did have another look and couldn't come up with any closer match. I'm leaning towards those skirts in your first pic are custom fitments, cut down/extended or from another car entirely and modded to fit an R34 sedan. I would've thought someone in Japan had them and taken a photo at some stage over the last 2 decades but there's nothing. Someone out there must know surely.
×
×
  • Create New...