Jump to content
SAU Community

Recommended Posts

Video footage of last weeks South Australia Time attack. Our sponsored vehicle is Topstage's carbon S14. 2015 built ceramic ball bearing ATR45SAT turbocharger survived engine failures, melted exhaust manifold, and this time fire from hydraulics fluid leakage.  Still managed to take first in rear wheel drive class.

winner.jpg

 enginebay.jpg

fire.jpg

burntenginebay.jpg

 

Product update for ATR43 RB bolt on series with 3 inches dump pipe suited for Rb25det and Rb30ET.

Available using ATR / SS series as well as Garrett GT / GTX CHRA. 

Housing's available in T3 .63 and .82, internal gated with 38mm port. Externally gated housings can also be supplied. More details are on our site, or simply send us a PM.

frontwithdump.jpg

Inside the dump pipe assembly.

turbinerear.jpg

 

  • Like 2

Little video to share about Jason Ferron's drifting session at Calder park few weeks ago. Video's been put together by the Drift Junkie Andrew Sparrow, do check out their Youtube channels about he's R33 GTST build.

Jasons's car is powered by one of our high flowed R33 GTST turbochargers making around 310rwkws on E85 fuel.

 

On 02/08/2019 at 11:14 PM, hypergear said:

Product update for ATR43 RB bolt on series with 3 inches dump pipe suited for Rb25det and Rb30ET.

Available using ATR / SS series as well as Garrett GT / GTX CHRA. 

Housing's available in T3 .63 and .82, internal gated with 38mm port. Externally gated housings can also be supplied. More details are on our site, or simply send us a PM.

frontwithdump.jpg

Inside the dump pipe assembly.

turbinerear.jpg

 

that's pure turbo-porn right there. 

  • 2 weeks later...

Got my car tuned finally by DVS JEZ after having some issues with "less competent" tuners in Canberra.  I know my setup is not ideal (return-flow) but was hesitant to spend money on restrictive parts if i needed to spend money first on fundamental running issues. 

 

Setup is as follows:

R32 Nistune ECU

EFI solutions Top fuel rail kit,  stock FPR with Bosch 0 280 157 187 495cc Injectors

Bosch Z32 AFM

3" Turbo back (bellmouth, port matched) 3" 100 cel 4" body Venom cat, straight through mufflers

Hypergear G2 21U Highflow

Greddy Profec OLED EBC

Custom Hard 3" intake pipe joining to stock Airbox, Return Bov

Return flow AVO Turboworld intercooler

R32 10psi actuator pre-loaded 3mm

GTR BOV

NPC clutch

SPlitfire coilpacks

Standard Walbro 255 with the wiring mod. 

 

Overall result is pretty good but quoted from Jez couldn't get more out of it "too prone to detonation", note the 230kw run was abandoned. so running 223Kw on 16psi

 

Now i know its running right i am looking to buy a new intercooler either HDI or Plazmaman and the 5" body 100cel 3" cat and then getting the tune tidied up a bit. 

 

My initial goal was to make the most responsive setup compared to stock turbo running 98 and airbox (hate the sound of pod filter) hence g2 profile choice. Can see my old tune in second pic of stock turbo and breathing mods.

 

Tao what do you think of the result? Besides changing the above (intercooler and cat)  and staying on 98 and an airbox (happy to modify it), is there anything else i can do to increase response/boost response.

 

Kind regards

Patrick 

 

 

 

 

hypergear 21u g2, nistune, dvs tune.jpg

old tune stock turbo, inj,afm, return flow, safc.jpg

21 hours ago, Dose Pipe Sutututu said:

Charge temps are too high, your cat is fine.

 

Yeah right. Well the plazmaman street series is a bar and played and the hdi is tube and fin. 

Those are the two I'm looking at at this point as reasonable options

1 hour ago, Pattey21 said:

Yeah right. Well the plazmaman street series is a bar and played and the hdi is tube and fin. 

Those are the two I'm looking at at this point as reasonable options

Don't bother with the Plazmaman Street Series, they're as good as a HDi.

Get the HDi GT2 coolers, they're pretty decent for the money you're paying, yes return flows "make" power on E85 setups, because that fuel suppresses so much knock it doesn't matter how hot your charge temps (IATs) are.

Cooler air = Denser Air = Less knock

Time to cut a hole in your body work :)

 

  • Haha 1

The car needs a big front mount cooler,  Go for Aero flow 600x300x100mm for a good budget cooler. Also the G2 model is a factory replacement, to get more power you will need the G3 or bigger profiles. 

27 minutes ago, hypergear said:

The car needs a big front mount cooler,  Go for Aero flow 600x300x100mm for a good budget cooler. Also the G2 model is a factory replacement, to get more power you will need the G3 or bigger profiles. 

Hi Tao, 

Thanks for the response.

when I was first bought the turbo you mentioned with the right supporting mods it could make 250kw.

Reason for going g2 was wanting as close as possible to factory response as per your results below, where I seem to be making similar power but at 16-18psi instead of 13.

Did you manage to achieve above 230 with this turbo?

Guess I want to see if it's worth my while changing cooler and get the tune tidyed up a bit and try make close to 250.

 

Kind regards

Patrick

 

FB_IMG_1566566458691.jpg

FB_IMG_1566566466459.jpg

The highest result out of the G2 profile lot was from Dr.Drift's personal R33 back in 2010. That pulled 253rwkws on pump 98 fuel.  

253rwkws.jpg

On 24/08/2019 at 7:36 AM, hypergear said:

The highest result out of the G2 profile lot was from Dr.Drift's personal R33 back in 2010. That pulled 253rwkws on pump 98 fuel.  

253rwkws.jpg

Sent you a pm ?

Had a chat with Dr Drift. His had a ext gate and adj cam gears. He did have a return flow though.

Sent Tao a message about upgrading to a g3 with BB

Edited by Pattey21
8 minutes ago, lexxi32 said:
11 minutes ago, Dose Pipe Sutututu said:
[mention=88652]Pattey21[/mention] hub dyno vs. roller dyno - results will vary.

Not if there calibrated properly.

If they're calibrated properly a roller will read lower due to the energy loss via the roller/wheel contact.

Also different tyres provide different readings, you run say semi slicks on a dyno make x kWs and the next day run just normal street tyres and you'll end up with a higher reading of y kWs.

  • 4 weeks later...

Tao, the new 21u basic high flow that made 342rwkw with the free flowing turbine wheel, is that as responsive as the earlier version? 

How does boost response compare to the stock turbo?  Yours isn’t ball bearing so is it slightly laggier? 

I have a 2860 (similar to hks2530) on the rb25 and don’t want to lose that response.. 

 

thanks

 

It will definitely not be as responsive as a 2860. That is too small for a rb25det. 

New G3 high flow has the same response as the older version with more mod range and top end power. It is still very responsive for daily or track.

Thanks Tao, 

So a g3 high flow should get about 260rwkw on an r33 p98, as opposed to a 2860 around 220-230 do you think? 

How much difference in boost response? I’m getting about 9psi by about 2300rpm in 4th I think..

 

 

 

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...