Jump to content
SAU Community

Recommended Posts

Rather than making a new tool thread, any comments on this for getting off flywheel bolts? Would it be up to it? $169 on sale for jap made rattle gun, 425ft/lb (so about 575nm?). The $40 supercrap ones are 310nm....

transquip link

should be fine Adam - as long as you have the air pressure for it

there is a tool out there, but i cant find the name - its has a 3/4 inch fitting for a socket with a small arm attached to a swivelling long arm

you hit the long arm with it setup like an L so the down force from the hammer blow cracks the nut.

if i find it i'll post up

For flywheel bolts I've always just used a 1/2 inch breaking bar and socket...

How did you hold the crank still? With a rattle gun i can just ignore that issue. And its a good excuse for buying new toys!

Hey, you guys might be able to answer me.

Cylinder hones, whats better the flexible ones (with all the abrasive balls) or the ones with 3 straight stones.

Ive used the 3 stone ones before with pretty good success but never tried the flexi ones.

Cheers

How did you hold the crank still? With a rattle gun i can just ignore that issue. And its a good excuse for buying new toys!

You can get a tool that bolts onto two of the bell housing spots, and it locks into the flywheel.

I believe the Volkswagen one fits.

I also just had some piece of steel around that fitted the above job perfectly.

Hey, you guys might be able to answer me.

Cylinder hones, whats better the flexible ones (with all the abrasive balls) or the ones with 3 straight stones.

Ive used the 3 stone ones before with pretty good success but never tried the flexi ones.

Cheers

3 stone hone will take alot more of the bore out

ball hone is just to de-glaze the bore or to remove surface rust if oil ran away from one bit

should be fine Adam - as long as you have the air pressure for it

there is a tool out there, but i cant find the name - its has a 3/4 inch fitting for a socket with a small arm attached to a swivelling long arm

you hit the long arm with it setup like an L so the down force from the hammer blow cracks the nut.

if i find it i'll post up

You're talking about one of these; right? post-61153-0-84460800-1307628247_thumb.jpg Sidchrome Impact bar. Only ever seen 1/2" drive though.

Features

  • • Creates impact to shock frozen nuts loose
  • • 8 x torque multiplication with a single hammer blow
  • • No compressed air required
    I have one; Best. Tool. Ever. Well, except for ratcheting ring spanners...
    Link to sales; http://www2.blackwoo...04738&P=2028222

Edited by Daleo

Features

  • • Creates impact to shock frozen nuts loose
  • • 8 x torque multiplication with a single hammer blow
  • • No compressed air required
    I have one; Best. Tool. Ever. Well, except for ratcheting ring spanners...
    Link to sales; http://www2.blackwoo...04738&P=2028222

DO WANT! How much? I didn't see a price on the blackwoods link.

DO WANT! How much? I didn't see a price on the blackwoods link.

Sorry mate, missed the query...:blush: $165

Link; http://www.getprice....6--44917348.htm

You might do better, but at least an indication.

Cheers, Dale

Edited by Daleo
  • 3 weeks later...

Ill try and keep this thread alive!

Picked up this set to replace my lost 3/8" repco gear..

IMG_0199.jpg?t=1309686078

Love the deep sockets :) Got it off ebay for a decent price but one of the ratchets is faulty!!! would i be able to swap this over at bunnings? pain in the ass sending it back to the seller...

Also picked up a new tool bag the Veto pro pac xxl-f :) from http://www.thetoolbloke.com.au/

veto-pro-pac-xxl-f-closed.jpg

IMG_0237.jpg

Next on the list is some ratchet spanners! not sure if i should go the flex head or the standard reversible fixed type.

  • 1 month later...

post-74990-0-42970400-1309730666_thumb.jpg

~$30 of awesome

Tie-rod end/pit-man arm puller, long gone are the frustrating hours of hammering the crap out of, prying, heating, WD-40'ing etc. Put it on, wind in the bolt, CRACK, done!

Want!

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...