Jump to content
SAU Community

Recommended Posts

nah i can never find it online

But I should get a photo of it and post it. This stuff is amazing, I used it on my dump and not one corner is even thinking of peeling off!

and it actually does its job!

Do you mean you stuck the heat shield directly to your dump pipe, or to the firewall to reflect the heat away?

Can you give me details of cost and maybe a phone number/email address of the place? I was about to buy some on line but will hold off if yours is so good Scott's buying some :)

Mine got a ticket Yesterday- thanks to the Mrs. parked in a Bus stop for 11hrs... $201

Interestingly, ticket read- Make- Nissan - Model- Station wagon.... would have like to have been there.

Oh, for the record, the Mrs isn't blind, the sign was obstructed by a tree (and I can't be bothered fighting that so don't bother)

bought a greddy oil filter relocation, strong AUS dollar and US ebay = $260 delivered to my door, thats a whole $120 cheaper than just jap thats before i pay them for postage too! Now just need to get an oil pressure gauge aswell

post-56886-0-70296500-1296633304_thumb.jpg

Do you mean you stuck the heat shield directly to your dump pipe, or to the firewall to reflect the heat away?

Can you give me details of cost and maybe a phone number/email address of the place? I was about to buy some on line but will hold off if yours is so good Scott's buying some :)

on the wall. so the wall doesnt buckle under heat or anything.. our firewalls are thin, i dont know if anyones notice that the car retains heat. well that because theres F all between the exhaust and the wall.

dont know off the top of my head. like i said scotts plan is to buy in bulk. maybe it'll come to you cheaper. in any case, wont need it unless you have a dump or have pulled off all the sheilding. but speak to scott for all the detailsthumbsup.gif

Cool, I thought that's what you meant. Scott's dump was posted to me on Monday so I expect I'll have it tomorrow. He suggested stick on heat shield from an ebay seller, and I've since found a couple of different ones that look pretty good. Even thinking of putting it around the IC plumbing to help with heat soak. I too have noticed just how much heat is retained under the bonnet.

I'll also get some wrap for the dump pipe which should help a bit. What's your opinion on those turbo "beanies"? Probably a bugger to put on considering where it's located on the M35, and not sure how effective it will be.

I use this guy.

http://cgi.ebay.com.au/ws/eBayISAPI.dll?ViewItem&item=180483039708&ssPageName=STRK:MEWAX:IT#ht_2145wt_905

Good product, I just want to find it in bulk if possible as its priced a bit steep when you need 4 or 5 sheets. (I have ditched the stock turbo/dump heatsheilds)

Cool, I thought that's what you meant. Scott's dump was posted to me on Monday so I expect I'll have it tomorrow. He suggested stick on heat shield from an ebay seller, and I've since found a couple of different ones that look pretty good. Even thinking of putting it around the IC plumbing to help with heat soak. I too have noticed just how much heat is retained under the bonnet.

I'll also get some wrap for the dump pipe which should help a bit. What's your opinion on those turbo "beanies"? Probably a bugger to put on considering where it's located on the M35, and not sure how effective it will be.

Yeh scotts below link is the stuff and the exact place as well.. putting it around the IC piping will probably make the IC Piping retain heat as its not able to escape. I also thought about the "beanie" thing but im not sure how strong our housings are, I know it would prevent a lot of heat in the engine bay, but i wouldnt want the housing to crack because it cant let off its heat..

i dont know. would look cool thought lol

I use this guy.

http://cgi.ebay.com....T#ht_2145wt_905

Good product, I just want to find it in bulk if possible as its priced a bit steep when you need 4 or 5 sheets. (I have ditched the stock turbo/dump heatsheilds)

this stuff is the shite!:bunny:

________

I bought some *meh* oil last night and some Motul engine flush. to hopefully get all the gunk and shit out!

also bought some pre mixed coolant, so it will be distilled.

a couple of $15 filters..

dropped the oil in the car. and found that there are small bits of alluminum shavings from when the shaft snapped. Im letting it drain right out until i get the turbo back.

Good thing I bought an engine flush! although I think i shouldve done it when i bought the car..

I dropped my oil last night.

I bought some *meh* oil last night and some Motul engine flush. to hopefully get all the gunk and shit out!

Gulf Western semi synth is a better oil than most people use. lol.

When are you getting the Sougi? Get me those two more while your there, I don't want to run out.

Gulf Western semi synth is a better oil than most people use. lol.

When are you getting the Sougi? Get me those two more while your there, I don't want to run out.

i was gonna go when the cars running again so i can run the GW stuff up there and back and do a change..

I use this guy.

http://cgi.ebay.com....T#ht_2145wt_905

Good product, I just want to find it in bulk if possible as its priced a bit steep when you need 4 or 5 sheets. (I have ditched the stock turbo/dump heatsheilds)

My sheet of that stuff has actually come unstuck slightly, its still in place but the sides have come off.. it may just need a 2nd 'press' to restick it and then it'll hold, Maybe. I'll try and get around to it on the weekend :P

I use this guy. http://cgi.ebay.com....T#ht_2145wt_905

Good product, I just want to find it in bulk if possible as its priced a bit steep when you need 4 or 5 sheets. (I have ditched the stock turbo/dump heatsheilds)

What do you think about this one http://cgi.ebay.com....e=STRK:MEWAX:IT ? Much bigger size (500mm x 500mm) and similar price.

Yeh scotts below link is the stuff and the exact place as well.. putting it around the IC piping will probably make the IC Piping retain heat as its not able to escape. I also thought about the "beanie" thing but im not sure how strong our housings are, I know it would prevent a lot of heat in the engine bay, but i wouldnt want the housing to crack because it cant let off its heat..

i dont know. would look cool thought lol

If the reflective heat shield was stuck around the return pipe (after intercooler), it would help keep the heat out and cool in. If the pipe doesn't get as hot from under bonnet temps, then it can't transfer as much heat to the colder air. I think insulation works in both directions.

I'm with you about wrapping the turbo in a beanie tho. Just not sure how it might affect life expectancy. In theory the turbo should be able to withstand its own heat (covered or not), and stopping the heat transferring directly across to the air side would be desirable but..... I'll have to keep asking around. It's certainly not the first thing that needs doing, but would be easier whilst under replace dump and exhaust. I bet I couldn't be bothered to do it later :)

Edited by Commsman

My sheet of that stuff has actually come unstuck slightly, its still in place but the sides have come off.. it may just need a 2nd 'press' to restick it and then it'll hold, Maybe. I'll try and get around to it on the weekend :P

The surface has to be cleaned like you've never cleaned anything before, i used pure ethanol to clean it off, but degreaser will work.. none of my corners on the previous one i used for the dump has even thought of coming off. plus its 3m

What do you think about this one http://cgi.ebay.com....e=STRK:MEWAX:IT ? Much bigger size (500mm x 500mm) and similar price.

If the reflective heat shield was stuck around the return pipe (after intercooler), it would help keep the heat out and cool in. If the pipe doesn't get as hot from under bonnet temps, then it can't transfer as much heat to the colder air. I think insulation works in both directions.

I'm with you about wrapping the turbo in a beanie tho. Just not sure how it might affect life expectancy. In theory the turbo should be able to withstand its own heat (covered or not), and stopping the heat transferring directly across to the air side would be desirable but..... I'll have to keep asking around. It's certainly not the first thing that needs doing, but would be easier whilst under replace dump and exhaust. I bet I couldn't be bothered to do it later :)

I've never heard of it, but no name stuff probably made in china wont last long. and its only rated up to 550 degree's, if your gonna tune it, your exhaust temps will be higher than that. the Dao's place stuff is i think 700degrees.

i thought you meant before the FMIC, yeh after would work but only really needed for pipe that the BOV is on, and if yours is stock, its made out of cast anyway so it doesnt need to be sheilded, its insulating itself.

I have only tried the 3M gear as it has the good sticking properties, I always clean the area with ethanol or metho before I apply it and have had no issues.

I wrapped my intake and bov pipe but from reading the forced induction forum, they say its a waste of time as the air isn't going to heat up in that short a time. That said, I have seen many race cars running it but they have much higher under bonnet temps and radiated heat.

A turbo beanie on our rear housing isn't a good idea, the casting is very thin compared to a Garrett and could easily warp with the weight of the exhaust hanging off it if it got too hot. I want as much cooling down there as possible with my setup.

If the reflective heat shield was stuck around the return pipe (after intercooler), it would help keep the heat out and cool in. If the pipe doesn't get as hot from under bonnet temps, then it can't transfer as much heat to the colder air. I think insulation works in both directions.

+1.

I intend to heat wrap the return pip on mine as I've found it can certainly get quite warm (much warmer than the exit side of the intercooler actually).

Installed a digital water temp gauge a few days ago as I had an inkling feeling that my water temps could be abnormally high.

A solid 81 degrees with it creeping to 86 on a warm day in peak traffic :D

bought a greddy oil filter relocation, strong AUS dollar and US ebay = $260 delivered to my door, thats a whole $120 cheaper than just jap thats before i pay them for postage too! Now just need to get an oil pressure gauge aswell

I've got that same kit, Rhet. It's a bit of a PITA to install, and may leak a bit because getting in there to tighten it up is hard with so little space to work in. Also, despite looking like braided oil lines, they're just regular rubber oil lines with the "braided" covering, unfortunately.

But it makes changing filters soooo much easier, so it's worth it!

I've got that same kit, Rhet. It's a bit of a PITA to install, and may leak a bit because getting in there to tighten it up is hard with so little space to work in. Also, despite looking like braided oil lines, they're just regular rubber oil lines with the "braided" covering, unfortunately.

But it makes changing filters soooo much easier, so it's worth it!

cheers for the info mate, what did you use to get it tight? just your hands? and i really am looking forward to not having my arm look like its been in a lawnmower after every oil change :laugh:

edit: out of curiosity what oil filter do you use? i imagine there would be a few options

Edited by horrace

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...