Jump to content
SAU Community

Recommended Posts

A little bit going on this week; had a new mirror painted to replace the damaged passenger side one (thanks Iain!); while I was at it also had my painter colour code the headlight eyebrows that I've had sitting in a drawer for almost a year now (thanks Mark!).

I don't mind the look, but I'm going to wait until after my mate details the car before I decide whether they're going on. This should be happening within the next few weeks.
Off to grab a new set of tyres later this week, and I'll finally be fitting my camber/toe bolts to minimise some of the rear tyre wear.

Also about time I did a diff oil change; not that impressed with my last LSD oil choice; does anyone have a recommendation?

I was either going to try the Nulon; http://www.nulon.com.au/products/Gear_and_Differential_Oils/Full_Synthetic_80W-140_Heavy_Duty_Limited_Slip_Differential_Oil/#.VAXOk_na7Lk

Or Castrol Syntrax Limited Slip 75W-140.

Any other oils I should be looking at?

I would use the Castrol, just because that's what I've been recommended through award gearbox.

They weren't very positive about the Nulon product, however that was more to do with how the product reacts to excessive heat. I've got some nulon in the open diff in the stagea, it hasn't blown up yet... Lol however I dumped it out of the 180.

  • Like 1

What a bargain! Where from?

from fle bay mate. They are dirty as he'll need a good scrub down and condition but other than that all is perfect need a resistor on the passenger side seat for the airbag plug and just need to open up the seat belt buckle and shave down the inside latch as are seat belt cards are thicker than the 350z's then all is a charm heated switches work as does the electronic forward back adjustments just the up and down are now manual but no biggie. You score a nice little side pockets on the seat wich now catches my phone when I fall out my pocket, it use to just slide under the seat and would be a pita to find. ;-)
  • Like 2

from fle bay mate. They are dirty as he'll need a good scrub down and condition but other than that all is perfect need a resistor on the passenger side seat for the airbag plug and just need to open up the seat belt buckle and shave down the inside latch as are seat belt cards are thicker than the 350z's then all is a charm heated switches work as does the electronic forward back adjustments just the up and down are now manual but no biggie. You score a nice little side pockets on the seat wich now catches my phone when I fall out my pocket, it use to just slide under the seat and would be a pita to find. ;-)

My biggest question is "where are the damn pics!"

  • Like 2

Mate very nice actually hold in in well wich was the main reason I wanted to try as with the stock seats if you take a corner fast and hard I'd end up on the passenger side 8-) the sit lower as well the passage is really low though to low infact so spacers are needed icon real the peddles perfectly just allowed a nice fit!

Got my car back on Friday after the exhaust wheel tried to make an escape a few weeks back.
post-128502-0-40750000-1410092384_thumb.jpg

Turbo was sent off to Hypergear for a Hiflow, just the smaller "G1" profile.
post-128502-0-48030200-1410092663_thumb.jpg

More bad news, exhaust was on it's way out. Cat in the dump was pretty stuffed and rust was starting to eat the rest (the rear section was pretty bad). So some presents from Scott were in order.
post-128502-0-97307100-1410093184_thumb.jpg

And a Blitz Nur Touring cat back to finish it. Selected mostly because of the time frame, it's nice and quiet which I wanted so it worked out nicely.
post-128502-0-79626700-1410093371_thumb.jpg

While it was in having this done I also had the cam cover gaskets done, the passenger side was pissing oil everywhere and apparently had a ton of sealant around it.

Big thanks goes to R&D Mechanical for doing the work, excellent work and very helpful. And a big thanks to Scott for fabricating the dump and front pipe and getting them too me very quickly and Stao at Hypergear for hiflowing the turbo.

  • Like 4

Got my car back on Friday after the exhaust wheel tried to make an escape a few weeks back.

attachicon.gifbrokenturbo.jpg

Turbo was sent off to Hypergear for a Hiflow, just the smaller "G1" profile.

attachicon.gifexhaust.jpg

More bad news, exhaust was on it's way out. Cat in the dump was pretty stuffed and rust was starting to eat the rest (the rear section was pretty bad). So some presents from Scott were in order.

attachicon.gifdump-front.jpg

And a Blitz Nur Touring cat back to finish it. Selected mostly because of the time frame, it's nice and quiet which I wanted so it worked out nicely.

attachicon.gifCatback.jpg

While it was in having this done I also had the cam cover gaskets done, the passenger side was pissing oil everywhere and apparently had a ton of sealant around it.

Big thanks goes to R&D Mechanical for doing the work, excellent work and very helpful. And a big thanks to Scott for fabricating the dump and front pipe and getting them too me very quickly and Stao at Hypergear for hiflowing the turbo.

Good work! Dyno chart?

Did my second oil change on my PNM35 over the weekend, happy to say it hasn't used a single drop of oil in a bit over 3 months. That was Penrite HPR10 which I discovered had been rerated (wtf?) to a 10W50, so I found some 5W30 on sale over the weekend, I thought I'd try it and see if there's any noticeable difference in fuel economy or performance.

Meanwhile the Commodore only had 2.5 litres left in it over the same period and had spent most of that time sitting still...sigh.

Not much new with my stagea.

Decided to paint my wheels gloss black instead of satin black, which i thinks a lot better.

was also considering getting a new rear bar, was thinking dolphin but i dunno. i have a tow var for the stag as i use it to tow our bikes etc so unsure at the moment.

post-107907-0-70566600-1410131982_thumb.jpg

post-107907-0-97631200-1410132078_thumb.jpg

post-107907-0-08119400-1410132124_thumb.jpg

Had a life f**king moment when car wouldn't kick over this morning... Tried to start it twice but wouldn't happen.

Thought straight away to look at the battery and BAM!

2014-09-08080139_zpsc2cbebb5.jpg

So did the usual "stick ur finger in the hole", there isn't anymore water but it needs a serious clean in there.

Gave my headlights a bit of a restore with the Turtle Wax kit.

post-135423-0-37050600-1410435305_thumb.jpg

post-135423-0-80978000-1410435337_thumb.jpg

Now the cracks show up real good!

So I thought I would cover some up with my home made, sheet aluminium eyelids.

post-135423-0-66504800-1410435509_thumb.jpg

My 4 year old daughter says they make the car look cranky! Win!

Painted using Supercheap Auto's Colour Spec paint.

Not a bad match, might even have a go at my roo damage unless someone has a red front left door and fender they don't need?

  • Like 2

Gave my headlights a bit of a restore with the Turtle Wax kit.

attachicon.gifHeadlight Before.jpg

attachicon.gifHeadlight After.jpg

Now the cracks show up real good!

So I thought I would cover some up with my home made, sheet aluminium eyelids.

attachicon.gifHeadlight eyelid.jpg

My 4 year old daughter says they make the car look cranky! Win!

Painted using Supercheap Auto's Colour Spec paint.

Not a bad match, might even have a go at my roo damage unless someone has a red front left door and fender they don't need?

feel like making some more eyelids mate? ;-)
  • Like 1

Well, hit the key in the Dayz and it started first kick. It has been a long haul since 8/12/2013 when she arrived on a trailer with a blown motor.

I have converted to RWD.

There are still a few things to get. A radiator and shroud. And a windscreen. They will come soon.

Can not explain how stoked my son and I were when it started first kick.

  • Like 1

feel like making some more eyelids mate? ;-)

A bit too time consuming, might be a bit quicker second time around but don't think I could do them any cheaper than the plastic ones you can get.

Glad you like them though.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...