Jump to content
SAU Community

How To Hotwire An R33

jhjones

By jhjones,
in General Maintenance

 Share

Recommended Posts

GTRAAH Experienced

GTRAAH

Posted
Posted

This is the BEST security you can have If you love your car then,

Microsensor

2-3 Immobilisers

A second car so you dont drive your baby everywhere and leave it out in the open.

A garage

Incase you dont have a garage, have a bat under your bed and if you hear your car chirp which means someone is near it before they even have a chance to do anything you have your bat ingraved into there forehead.

Maybe you will ave a broken window or a stuffed lock. But no way they taken the car.

Can someone tell me how they will take this car ^^^^ other then putting a gun to someones head.

PM-R33 Grand Master

PM-R33

Posted
Posted

Break into house while you are using second car.

Find keys in the house since they will most likely be in one of the common locations.

Unlock car.

Open garage.

Drive out.

Most common way cars get stolen. Hence why a hidden fuel pump kill switch is the best option.

karma_syke Collaborator

karma_syke

Posted
Posted

Break into house while you are using second car.

Find keys in the house since they will most likely be in one of the common locations.

Unlock car.

Open garage.

Drive out.

Most common way cars get stolen. Hence why a hidden fuel pump kill switch is the best option.

this and a steering lock bar, with the wheels turned so they are pointed towards the kerb, less chance of some one lifting the rear axle and towing your car.

it's bothersome, but i use it if i have to leave the car in a shifty place. Just an extra layer of security thumbsup.gif

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      Are you an oil nerd?

      By joshuaho96 · Posted

      You're not wrong but 5W30 at 100C is like 10 cSt vs 25 cSt for 10W60. If we think in terms of viscosity margin 10W60 will probably still be ok at 130C but 5W30 is probably too little. It's absolutely shocking how hot the oil gets in something like a stock FL5 from only ~3 minutes of use on the Nordschleife. I would not risk taking a car like that to anything remotely intense without a ton of work done for cooling. Heat shielding on the manifold/turbo/downpipe, oil coolers, etc. 
    • Kinkstaah
      Are you an oil nerd?

      By Kinkstaah · Posted

      I think the concept is highlighting the various scenarios where thicker oil helps, and thicker oil potentially doesn't help and only generates heat and costs power, in turn for safety which isn't actually any safer (unless you're going real hot). If anything this does highlight why throwing Castrol 10w-60 for your track days is always a solid, safe bet. 
    • GTSBoy
      Are you an oil nerd?

      By GTSBoy · Posted

      Jason should have shown a real viscosity vs temp chart. All the grades have very little viscosity difference at full operating temperature.
    • dbm7
      BCNR33 Blower Motor Resistor - Testing

      By dbm7 · Posted

      Oops... I meant to include the connector  view... BR/W - power from fuse L/W - motor negative to fan control amp (and off to HVAC pin19) OR/B - PWM signal (from HVAC pin20) B --  ground  
    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      Yep, if you are applying filler it sounds like there is something wrong with the body lol. Safe to assume there is going to be a lot of sanding going on if your still applying fillers.  Picture a perfect bare metal panel, smooth as glass. You lay down your primer, it's perfect. (why are you going to sand it?) You lay down the colour and clear, it's perfect. No sanding at all took place and you've got a perfectly finished panel.  You won't be chasing your tail, sounds like you were prepping to start laying filler. If your happy with the body after the sanding, there is some bare metal exposed and some areas with primer, no issues at all, start laying the filler. You are safe to lay filler on bare metal or primer (of course check your technical data sheet as usual for what your filler is happy to adhere to).  This isn't a 100% correct statement. There is primer that is happy to adhere to smooth bare metal. There are fillers that are happy to adhere to smooth bare metal. Just make sure you're using the right materials for the job.  Typically if you are using filler, you would go primer, colour and clear. I've never seen any instances before where someone has laid colour over body filler (maybe this happens, but I haven't seen it before). So your plan sounds pretty normal to me. 
×
×
  • Create New...