Jump to content
SAU Community

Recommended Posts

Anyone know if, during daytime use, headlights are mandatory? I have a track bike which is road rego'd for insurance purposes, and obviously has no headlights, but I'd like to take it out every so often. It is fitted with brake and tail lights and I could easily fab up some indicator brackets too. Just the lack of headlight is the issue. Obviously would never ride at night without it...

I'd say yes they are, or the bike technically isn't in roadworthy condition and would void your insurance anyway? Dunno just my thoughts

MO WTF? Already? That build didn't take long at all, felt like less than a week.

If it was built but his cousins like his original guards, then it probably has daewoo pistons and a Hyundai excel block

Nah I'm almost done. Couple of f**k ups by ikea I had to fix though, like oversized pre drilled holes..

It's just time consuming. I saw your car.. Was gonna box it in with trolleys.. Maybe next time

Haha did you have to get some parts swapped over or something? What did you buy, anyway?

Ah, yeah, I was in Kitchens today.

Did you swing by our new lolly bar? $2 per 100g. It's aight. But can't have much too unhealthy yo :P

Birdy, what do you think of Martini Racing gearbox oil?

I have no experience with it, though Martini products are generally very good, so I doubt you'd see their name on something shit. I could be wrong, but from memory Martini are just rebranders of decent stuff from other manufacturers.

Haha did you have to get some parts swapped over or something? What did you buy, anyway?

Ah, yeah, I was in Kitchens today.

Did you swing by our new lolly bar? $2 per 100g. It's aight. But can't have much too unhealthy yo :P

Nope, one kit. "Hemnes" set of draws. Finished them off today. Found more issues.. One of the biscuit joins weren't drilled deep enough and pushed through the face side snapping the face of the draw. All the screws just keep threading themselves. Fixing sooooo many of ikeas f**k ups..

/whinge

Tl:dr

Yeh next time I'll just buy premade. Lol easier less problems or just build my own from scratch

I have no experience with it, though Martini products are generally very good, so I doubt you'd see their name on something shit. I could be wrong, but from memory Martini are just rebranders of decent stuff from other manufacturers.

They make their own stuff now I believe according to mate who works there, ie used to sell endless 600 brake fluid, now have their own.

Engine and gearbox now filled with martini, yet to start it though. Motorbike soon to also have martini

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • What copper washer do you guys use on the bleeder bolts? The existing one I have I had no idea where to find it in a local store, I did buy some online but that are only 1mm thick whereas my old one is 2mm+ thick and when I put the new washer out and squeeze the top radiator hose I can hear a bit of air but not with the old one. Does this matter? The new one doesn't leak, but the inner diameter is a bit loose whereas the old one threads on the bolt.
    • Howdy all, after being out a few weeks ago on a spirited drive in my GTR I have 2 issues that oddly have appeared at the same time. Whilst accelerating quickly through the gears all of a sudden i’ve lost power at the top of third gear (below redline around 6000rpm) for no obvious reason.    From that point onwards the car has been running rich on idle, won’t really rev under load without a ton of black smoke and the odd backfire, and dying as a pull up to a set of lights unless I keep the revs up around 1500rpm. In addition when shutting down the car that same night (I was 10 minutes from home) I noticed one of the turbos was significantly noisy on wind down when shutting off the engine. After letting the car cool down overnight it starts up fine, although once it gets to temp the revs start to creep up and down, the exhaust is darker than it should be and it also sounds like it’s running rich (fat note) I’ve put a new set of plugs in it - no change, the old plugs all seemed OK with two of them being somewhat richer/fueled up than the other 3 with 1 being borderline. I’ve smoked tested the intake system via the front of the Turbos, found a split vacuum hose going to the factory boost gauge sender, which I have since replaced.  Also found another leak on the gasket coming off the rear turbo outlet, have also replaced this. After fixing both of these leaks - still have the running rich issue. I’ve also tried another pair of AFM’s - no change here After pulling off the front turbo intake pipes, there is obvious shaft play in the front turbo, which now hisses loudly on light revvs although I can’t see why this would make the car run funny even under idle. I’m curious to know why it’s running rich before I potentially replace/rebuild turbos. The car is completely stock <50,000kms  other than an exhaust. Oil and coolant are all clear. I haven’t bothered with coil packs as it looks like they won’t be the issue due to condition of the plugs. Any help appreciated as I cry myself to sleep!
    • No probs at all. I used to love trying to dig up obscure info for those in need where possible going back 20+ years on SAU.  I did have another look and couldn't come up with any closer match. I'm leaning towards those skirts in your first pic are custom fitments, cut down/extended or from another car entirely and modded to fit an R34 sedan. I would've thought someone in Japan had them and taken a photo at some stage over the last 2 decades but there's nothing. Someone out there must know surely.
    • Welcome mate. Any pics? Even with a DE I'd be well happy if I had that as a 1st car. 
×
×
  • Create New...