Jump to content
SAU Community

Recommended Posts

What is this cool event on the 28th of September or is it super hush hush? I might need to book a loooooooooooong weekend, my 30th on the 27th.

it's something that I need to finalize booking in.

All Melb central/surounds, and will be amazeballs

duct tape....answer to everything

if you need a spare wheel for the weekend I could provide a 245 17? mmmm lightweight

I've got some 17's with 235's or 17's with 255's that aren't on the car right now if you want to borrow a set for the weekend :) It's going to be a great day out

It's all good guys, used duct tape and it seems to have done the trick..... on a serious note, won't have time to fix broken studs before Sat. Thanks fellas.

racing badge...yeah whoever put it there should be shot, these are the std ones much nicer:

http://www.enkei.com/nt03m.shtml

They are standard Enkei badges, from the 90's. I think there's supposed to be japlish parables either side of the lettering but they don't last and end up being rubbed off somewhere through the years.

Nah man I know nothing about 32s only 33s

Doesn't matter what year, all 32R's look the same, why does everyone always seem to instal LH N1 vents goofy though?

They are standard Enkei badges, from the 90's. I think there's supposed to be japlish parables either side of the lettering but they don't last and end up being rubbed off somewhere through the years.

Doesn't matter what year, all 32R's look the same, why does everyone always seem to instal LH N1 vents goofy though?

No headlight changes or differences at all over the years?

So last night was driving down south rd and a divvy van was sitting at the lights waiting to turn right...

He ripped out of the turning lane without indicating, cutting off a driver and nearly causing an accident, then sat behind me for about 1km.

After this he floored it and cut into the bike/parking lane and overtook me on the left again without indicating, eying me off as he went past at 7000 odd revs. He then proceeded to cut in front of 2 lanes of traffic to avoid hitting a parked car.... once again, no indicator.

would have been close to double the speed limit by the end of it.

When in front of the first car, he chucks his lights on (presumably so as to avoid a complaint from the driver he nearly killed) and cuts off yet another driver in order to make it to a U-Turn spot.

He then turns the lights off and drives off at like 40kph looking at me and smiling like a knob.

wonder if i have an EPA coming? :/

cliffs notes: cop was driving like a fuckbag to prove he could get away with it and i'll probably cop an EPA because of it

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...