Jump to content
SAU Community

Recommended Posts

simone. mick says you has universal clutch tool!?!?!?

can i has use of for 10 mins?!

You may. I'll be home in Vermont South after 6pm, but I'm going out at 7:20 if you need it tonight. I can leave it in the letterbox if you want.

oh hai

new car is berry nice

hamish it has 2.3Lkit, 270deg cams, 1k injectors, clutch, flywheel, vipec and usual supporting mods with an evo 9 turbo on it

its tuned for 19psi and i havent driven it on 19psi yet, only 8psi and it flies / pulls awesome in every gear - made 240kw last dyno run

ah was just surprised the setting is even that low, as stock they run much higher?

then again you have a stroker... fun times.

mods collecting dust in my room and garage, need to strap them on to unleash the 2L milk carton fury

Anyone installed one of the HKS SSQ Blow off valves? Looking at purchasing this:

http://www.ebay.com.au/itm/NEW-Atmospheric-Plumb-back-Skyline-R32-R33-R34-RB-BOLT-ON-Blow-Off-Valve-BOV-/151073396294?pt=AU_Car_Parts_Accessories&hash=item232cad1646&_uhb=1

Wondering if it's better than the others on the market?

Ssq is fnf spec

yeah ive got no idea how it runs less boost than stock

my understand, at least from skyrine was you could never run less boost than the actuator spring

no idea how this is working

but its got an eboost 2 switchable between 8psi, 13psi and then 19psi

but stock i think is 19psi

Probably actuator is adjustable/weaker spring?

EJ20s will run less boost than actuator pressure if they're in Limp mode, I don't understand how it happens even without running the factory boost solenoid but it won't let it past 4 psi. I guess it must yank shitloads of timing to keep it down?

no idea

ill have to do some reading on the evo 9 turbo and the controller setup

my understanding was from the skyline setup

where you must run the minimum spring level, you can run higher, but not lower

Anyone installed one of the HKS SSQ Blow off valves? Looking at purchasing this:

http://www.ebay.com.au/itm/NEW-Atmospheric-Plumb-back-Skyline-R32-R33-R34-RB-BOLT-ON-Blow-Off-Valve-BOV-/151073396294?pt=AU_Car_Parts_Accessories&hash=item232cad1646&_uhb=1

Wondering if it's better than the others on the market?

get one of these.

http://gfb.com.au/products/blow-off-and-diverter-valves/deceptor-pro/deceptor-pro-ii--inside-car-adjustable-adjustable-bias-venting-diverter-valve2013-08-04-02-40-32855251378-by-gfb

you can adjust from plumb back daily to fully FnF style or in between all with a switch in the cabin!!!!!

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...