Jump to content
SAU Community

Recommended Posts

Benita Grace Claire Hampton

Born 13:59 15/1/15

Both mum and bub are doing amazingly

No hate today

<3

BGCH

Sounds like a new party / rape drug

But congratulations :)

why 9000? its like saying pushing your turbo to 40psi. its a nice number but unnecessary if setup properly (for street and occasional track use)

congrats hamish. when you getting torago?

it__s_over_9_000____by_savi7-d5275y7.jpg

what turbo's did the car come with again fagmatron?

If it's GTSS' as my memory seems to be telling me then they might be a titch small for the 3.0

GT-SS

They'll be fine; it'll be a response monster

a responster

  • Like 1

GT-SS

They'll be fine; it'll be a response monster

a responster

go with -5s.

the GTSS are perfect on mine, rb30 bottom end = run out of puff.

like you.

better order some of that nasal delivery shit. cocaine in a bottle.

Top end is for track cars and dyno queens

On the street the low and mid range is where it's at

Besides, I'd have no less top end than this RB26, which doesn't appear to be lacking

rb26_graph.gif

Just a much more linear and torquey low/mid; borderline naturally aspirated. Wouldn't please Grant.

Yes you can whack a huge turbo on an RB30, but to me that defeats the point of a displacement upgrade which usually done for a better low and mid range, especially when your enormous power exceed usability on the street - you end up sacrificing the extra response for power you never see touch the ground.

what turbo's did the car come with again fagmatron?

If it's GTSS' as my memory seems to be telling me then they might be a titch small for the 3.0

congrats

and yeah 3.0 sell em for -5s!

inb4 birds is already hypergear fanboi tho

also

hypergear hypergear hyperge..

grats hatish.

hibiki for you???

alvin pls.

give hibikis nao

GT-SS

They'll be fine; it'll be a response monster

a responster

it will be a response monster that's for sure, but i'd prefer a little more up top

TBH I would be able to lap faster in my old 33 than al's, and they were running virtually the same power and suspension setup, only difference was that 0.5l

alvin pls.

give hibikis nao

it will be a response monster that's for sure, but i'd prefer a little more up top

TBH I would be able to lap faster in my old 33 than al's, and they were running virtually the same power and suspension setup, only difference was that 0.5l

how can there be too mut powah?

and no hibiki for you.

GT-SS

They'll be fine; it'll be a response monster

a responster

I bought a pair of gt-ss off a bloke who plonked them in his 2.8 originally. He took it out cos it ran out of puff around 5-6k from memory.

If 3.0, just get -5s, will be responsive enough.

alvin pls.

give hibikis nao

it will be a response monster that's for sure, but i'd prefer a little more up top

TBH I would be able to lap faster in my old 33 than al's, and they were running virtually the same power and suspension setup, only difference was that 0.5l

Yeah but Al's was RWD running 265 KU36s

AWD and some 265 R1Rs will clap dem cheeks

Can always change down the track if it sucks - retune and turbo swap. The GT-SS are worth more than the Garretts.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...