Jump to content
SAU Community

Recommended Posts

Andrew from AM Performance ran his car on the same dyno at Jason, and made 308rwkw, then went down the road to the Willall mainline and made 249rwkw. just to give you an idea of the difference

at the end of the day its for tuning, not for bragging

tis annoying how some dynapack owners dont calibrate it properly though.

trent runs the same dyno and has his reading within a few kw of a dd for when he does printouts.

makes a lot more sense for comparisons

tis annoying how some dynapack owners dont calibrate it properly though.

trent runs the same dyno and has his reading within a few kw of a dd for when he does printouts.

How is reading DD like dynos "properly" calibrated?

How is reading DD like dynos "properly" calibrated?

What he means is that most dynapack dynos read significantly higher than a DD dyno in the norm and trents one pretty much is spot on with other DD ones which arent happy so it makes for a better comparison with other peoples results.

What he means is that most dynapack dynos read significantly higher than a DD dyno in the norm and trents one pretty much is spot on with other DD ones which arent happy so it makes for a better comparison with other peoples results.

There are 4 calibrations for different regions (like usa which use old std) and test procedures:

SAE

DIN

and two others i cant think off.. lol (as i never change it)

some of the operators in sa seem to always run theirs in the old standard which inflates power... have bought this up a few times with them as they give the dyno a bad name even though its actually far more accurate.... hell i could have got a 4wd roller for the price of my new 2wd dynapack...

on top of every dyno sheet from dynapack is the correction type used, if it isnt in SAE J1349 (2004) ask it to be changed. Also like any dyno make sure the Air intake temp probe is set to ambient and is reading real ambient temperature

Almost a direct overlay of my T67 set up on the same type on dyno with the same correction... Actually uncanny!

Which begs the question, how much boost?

Yellow run was 17.10psi

Green run was 18.36psi

There are 4-5 calibrations for different regions (like usa which use old std) and test procedures:

SAE J1349 (2004)

SAE

DIN

and two others i cant think off.. lol (as i never change it)

some of the operators in sa seem to always run theirs in the old standard which inflates power... have bought this up a few times with them as they give the dyno a bad name even though its actually far more accurate.... hell i could have got a 4wd roller for the price of my new 2wd dynapack...

on top of every dyno sheet from dynapack is the correction type used, if it isnt in SAE J1349 (2004) ask it to be changed. Also like any dyno make sure the Air intake temp probe is set to ambient and is reading real ambient temperature

SAE

DIN

and two others i cant think off.. lol (as i never change it)

some of the operators in sa seem to always run theirs in the old standard which inflates power... have bought this up a few times with them as they give the dyno a bad name even though its actually far more accurate.... hell i could have got a 4wd roller for the price of my new 2wd dynapack...

on top of every dyno sheet from dynapack is the correction type used, if it isnt in SAE J1349 (2004) ask it to be changed. Also like any dyno make sure the Air intake temp probe is set to ambient and is reading real ambient temperature

Is there SAE J1349 a separate setting to SAE? I always have used SAE... and "inflates power" is surely a relative term, regardless. So long as all details are considered it is what it is, I'd call it more "inflated" where people reduce smoothing in the hope spikes will boost the #s.

Unopened rb25

Gt3076. 82 IW

Caltex eflex

310rwkw 16psi

320rwkw 18psi

Leak in cooler piping/plenum that needs to be fixed then its back for a tune as it wont hold more than 16 psi and sounds like I got a midget under the bonnet blowing a trumpet lol

Damn that lil midget bastard gets around! he was under my bonnet too lol

Unopened rb25

Gt3076. 82 IW

Caltex eflex

310rwkw 16psi

320rwkw 18psi

Leak in cooler piping/plenum that needs to be fixed then its back for a tune as it wont hold more than 16 psi and sounds like I got a midget under the bonnet blowing a trumpet lol

  • 1 month later...

Andrew from AM Performance ran his car on the same dyno at Jason, and made 308rwkw, then went down the road to the Willall mainline and made 249rwkw. just to give you an idea of the difference

at the end of the day its for tuning, not for bragging

and the funny thing? both are mainlines.

use this formula:

mods: PowerFC, GT3037 Garret, 0.6 cpm Cover, 0.63 rear housing, 18psi, Nismo 555s, 3inch turbo back exhaust, 600x300x75mm intercooler, Split Fires, NGK BKR7E plugs, Water Methanol injection, 275ml min nozzle.

fuel: Shell 98

power: 320rwkw, 720nm Torque @ 3200rpm

oil: Shell Helix 5w40 fully synthetic

useage: Every day

lifespan: Lasted 4 years, until I decided to upgrade to RB2530. Engine was still 100% compression wise when sold. 165psi accross all 6 cylinders.

failure: none

comments: Was an awesome car to drive. I did all the tuning myself.

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four-speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to its full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so stupid hot in there, that made it all the more easy -after I was standing there looking at the car and said 'f**k it'- to finally remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
    • Thanks for that, hadn’t used my brain enough to think about that. 
    • Also playing with fire if they start to flow more air down low than what the stock twins can. It's not even up top you need to worry, it can be at 3000rpm and part throttle and it's getting way more flow than it should.
    • Any G40/1000 or G40/1250 results out there?  
    • You still want a proper tune on the stock ECU though. Stock tune + stock ECU with GT-SS/-9s is probably playing with fire if you're running more than stock airflow/power.
×
×
  • Create New...