Jump to content
SAU Community

Recommended Posts

At the time I was happy to buy a clean mostly std 96 without ABS , just more crud you can't legally remove and expensive boxes that can fail . Couldn't escape the drivers handbags though .

If I had to rebuild a 25 short I'd use Neo style rods pistons and lid .

A .

Nope, though I personally wouldn't go for the HTA2868 twins that are available - I doubt the combination would match up overly well to an RB... especially when squeezed into those little housings. Owen Developments sell them though, and someone installed a pair on his GTR but then had an engine failure which set him back something fierce so not sure if or when that will be back together. It seems folly to me to try and push past the "-5s" flow at this stage in those housings, I guess the closest to a setup like that which I would like to see would be more like upgrading low mount T517Zs to use the 68HTA wheels, probably less likely to surge and generally be a better match.

Fair point. I had a feeling that little rear housing would/is the bottle neck. -5's it is then!

Fair point. I had a feeling that little rear housing would/is the bottle neck. -5's it is then!

What would be nice would be an HTA equivalent of -9s IMHO, something that flowed a bit more than -5s but spooled better than any low mount bolton option currently available. Wonder if the would bite :-D

Sent from my GT-I9505 using Tapatalk 2

ata-cid='6899132' name='Piggaz' timestamp='1371733825' post='6899132']

What would be nice would be an HTA equivalent of -9s IMHO, something that flowed a bit more than -5s but spooled better than any low mount bolton option currently available. Wonder if the would bite :-D

Sent from my GT-I9505 using Tapatalk 2

I actually thought something along those lines after i posted it. Same peak figure flow of a -5, just come on even earlier. I would be so down for that!!!!!

I actually thought something along those lines after i posted it. Same peak figure flow of a -5, just come on even earlier. I would be so down for that!!!!!

Never satisfied :P

Don't even know if they make something like that.

Nothing really has happened for the low mount GTR setup for years.

Unless you have a 35gtr :ph34r: they have been making some crazy numbers lately with the HTAs

Don't even know if they make something like that.

Nothing really has happened for the low mount GTR setup for years.

Because going to a bigger single is winning - and it seems people are more keen on winning these days :D Twin scroll HTA3586 would go nicely! ;)

Because going to a bigger single is winning - and it seems people are more keen on winning these days :D Twin scroll HTA3586 would go nicely! ;)

I have no doubt that a well matched single would yield a better result... Just can't give up the "standard look" :/

^ just black everything like Mat, for ninja stealth look lol

Lol i think Paul killed mine in terms of the stock look..... But mine is :ph34r: spec..... I was originally going to do the front housing of the turbo BUT it looks too good and i am kidding myself if i think i can hide it :laugh:

Yours looks more stock than most RB25DET engine bays, defect free I guess?

then again it depends on the copper :)

I've been pulled over in my shitbox and popped the hood. I told the copper it's stock and he was like yeah it looks pretty stock to me, close bonnet.. happy days.

Maybe the stock airbox saved me from a defect, hopefully be getting turbo/manifold by Q3 after my tax returns hehe

A low mounted 6boost I think could almost get away with it, I just need a heatshield made up and it will come as close as it gets I think.

If you are fouling the front housing on the 3037 then the HTA version wouldn't have much chance as it has a bigger front cover again, i should have got a side by side pic but i didn't think of it at the time!

If you are fouling the front housing on the 3037 then the HTA version wouldn't have much chance as it has a bigger front cover again, i should have got a side by side pic but i didn't think of it at the time!

I even asked you to :P On that note, DYNO PLOTS???!!! :P

I think it could be done, engine mount moved/modded but its a PITA

You have done an epic job! Hurry up and get results ;)

I even asked you to :P On that note, DYNO PLOTS???!!! :P

Did you? Oops...

I sent an email and Adam will do it when he gets a chance :) You waited this long, so wait some more hehehe

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Thanks guys! Some pics attached 😋
    • Big enough for you, Jackie, and some puppers mate! I vote some GSDs, but I am biased   How big of a block is it on?
    • Well, fun day was had, I finally found a house that will do me just fine, 1980's brick build, but with full fresh renovations, plus new colour bond fencing all round so puppies are incoming 🐕, and water tanks for the garden, and it's located in West Goulburn..... @Duncan 🫡, so day trips to Wakie to watch cars going Zoom will be on the cards In the end it cost well under my budget and was actually better than alot of the more expensive joints I was looking at, it is in a good area, close enough to the shops, public transport, and the Wollondilly River Weir,  and the great walking paths along the river, but far enough away from town to see minimal traffic The deposit is dropped, the conveyancer is conveyancing and I should get the keys in a week or 2 as the property is currently unoccupied  As with everything I own, I'm doing up a modifications list, as it doesn't have solar, that is first up on the big list, all of the panels and enough batteries to keep the joint warm, or cool, followed by a largish carport out the front, the small list, which will start as soon as I have keys, is some security stuff, like cameras, screens, and the usual "crazy prepper" additions that weird old people like (mouse holes to stick shot guns out of, and the usual man traps that the average person installs for the unsuspecting and unwanted guests 🤣) The gardens front and back are OK, but, not to my standards or liking, so landscaping will be a fun job to start getting into, so when spring is sprung I'll do a heap of planting, lots of natives and vegetables is the plan, the old owners were more "Old English Garden" type, so basically Roses and other weird looking things that are destined for the green waste bin One thing that is staying garden wise is a nice established hedge out the front, it is about 5 foot tall and covers the whole front of the property from prying eyes As for the car hoist, the roof in the garage has some height to it, but, I'll need to get an installer out to see what can be done, width wise may be a issue, but my building inspector will be getting back to me over the next week with his recommendations  Small, but cosy     
    • I tried to get in contact before I went to QLD you didn’t respond, then I tried to contact you in r31 club.  I thought you fell off the earth or something haha.  I will grab it off you but unknown when I will be up that way 
    • I think that might be in the question. He is going very low, and I think the standard GTR ones are simple tripod joints (like the rear NA/S chassis ones), not proper CVs (like R chassis turbo/GTR ones). Proper CVs take the misalignment better than tripods.
×
×
  • Create New...