Jump to content
SAU Community

Recommended Posts

As for torque monster....its only 3.2L

No engine with only 3.2L to play with will be a low down torque monster

Arh yeah, you should climb into my 32 one day, only 2.6 and a massive torque monster

I was in Canberra over the weekend with the 34 doing the hill climb

  • Like 1

You can't tune past 25 on 98, if you're lucky.

You'll get heaps more on E85. e.g. my car made 100kw more with 2-3psi increase on E85, over 98

Paul was saying something similar and I will do an E85 tune but not a lot of chances to use it here and I am happy enough with how it runs on 98, it is fun as a DD :)

It will be interesting to see what the E85 produces with this builds specs ?. Looking at some posts it seems to vary quite a bit from car to car ??

Dont get me wrong, this car gets up and goes pretty good and is easy on the bends with the more linear acceleration and the drive train seems great, smooth and planted , but pushed really hard ??????

The thing is. Why get a big hp turbo and not use it to its potential?

If you really wanted response then you could have gotten a smaller single that would spool quicker and get you to 380/400 kW

I was learning, took a T78 off and put the 6262 on and it went much better, still not happy BUT accept for the cams I kept most of the bolt ons and did the 3.2 build. If I am not happy I will do something about it,.

But for now happy enough, tomorrow ???

The thing is. Why get a big hp turbo and not use it to its potential?

If you really wanted response then you could have gotten a smaller single that would spool quicker and get you to 380/400 kW

On petrol? As said earlier, you're really boost limited on 98, WHICH HE IS ON ATM!

Give the bloke a chance to get it drunk and turn the wick up.

I can't see a smaller turbo on 98 getting close to the 400 mark.

Far too many guys just look at the peak number. I'm sure if guys got in it and drove the thing they would get out pretty impressed. Midrange grunt > topend. Keep the top end for pissing in your mates pockets in the pub.

Wow. Tell us what you really think Paul.

Anyways. Wouldn't be a problem if he wasn't hell bent on response. But now it's a double standard.

Not my car.

Paul never says what is on his mind, wimpy fag !

Where is the double standard ?

I expected more but happy with what I have, it is a well balanced DD, goes quick and holds the road like shat to a blanket, all good :wub:

Just a couple of tweaks and :)

  • Like 1

Its all good, like Paul said no doubt it will be a torque monster. More boost and ethenol will make heaps of difference. If your spark is failing which sounds like it may be the case, id consider getting a Morris tech ignitor like myself and Paul (I know you already have spitfire coil packs).

And I agree with Micks post.. CRD are a rip, I've seen some of their invoices and they prey on the unknowing. And their tunes are not the best in the business.

Best result would be.

Get password, take to UE, get re-tune.. Happy days.. If they built the engine properly, it won't blow up

  • Like 1

$1600 :(

It is hard being in this situation, I have an expensive build and once I change shops my warranty goes out the window and the new shop does not put their warranty on the car ?

There are a few things I am not happy with and will try and work it out first.

And 1600 for a petrol tune is f**king bullshit.

If they gave me 1600 to tune my car I'd still tell them to stick it

Edit 1600... Still f**ked

you get the invoice after the tune , what the f**k can you do

Its all good, like Paul said no doubt it will be a torque monster. More boost and ethenol will make heaps of difference. If your spark is failing which sounds like it may be the case, id consider getting a Morris tech ignitor like myself and Paul (I know you already have spitfire coil packs).

And I agree with Micks post.. CRD are a rip, I've seen some of their invoices and they prey on the unknowing. And their tunes are not the best in the business.

Best result would be.

Get password, take to UE, get re-tune.. Happy days.. If they built the engine properly, it won't blow up

The 34 has built in ignitors, the Mojo LS2 kit is what i'm going to get

  • Like 1

Arh yeah, you should climb into my 32 one day, only 2.6 and a massive torque monster

I was in Canberra over the weekend with the 34 doing the hill climb

I'm sure it is torquey.....for a 2.6

but compare it to...oh I dunno a blown 6.2 LSA...both at road speeds and revs.

That's what I was getting at

Going to get it all done and dusted and work out what I want to do.

I will get the E85 flex tune soon.. and when I am getting that done I ask about ignitors . Spitfire coils any good ?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
    • So, a bit of a side trip, but one that might be interesting for people with JDM cars and japanese head units. I know @Pac previously posted about a carplay/android auto adapter he installed which used the AUX input, and @V35_Paul put in one of the Tesla style units that replace both screens. The option I went with was a Lsait LLT-YF-VER5.87_2 (https://www.alibaba.com/product-detail/Lsailt-8GB-Android-Multimedia-Interface-for_1601187633672.html). Price was $1,150 for a single unit although they are much cheaper if you are willing to buy 2....$857ea. Make you you get the version 2 not version 1, it is faster and has a better UI - this is the manufacturer listing: http://www.lsailt.com/product/348.html. BTW if you've never bought from Alibaba before, don't be concerned....these guys can't stay in business unless they are responsive, ship fast etc, they were excellent (probably faster shipping than most local places) So, this was my task for a lazy Sat afternoon....looks complex but was all done in a few hours (it probably helps that I had some of it apart before so it was a bit familiar). I also decided to add a HD USB drive recorded at the same time and the unit also supports an aftermarket reverse cam (if you don't want to retain factory) and also AV in and HDMI out It looks much worse than it is, in fact in was genuinely all plug and play (no custom wiring at all). This video was pretty good (skipped a few steps), unfortunately they are an Aussie seller but no longer sell this unit (I guess Carplay/AA adapters are easier to install and much cheaper) https://www.youtube.com/watch?v=T5hJfYOB8Dg
    • That still isn't a lot to go on. I don't have a Y50 Fuga Head Unit wiring diagram. I can say that a lot of nissans of that age shared head unit plugs, so if you are in Australia something like this would probably help: https://aerpro.com/app091# You plug that into the car loom, then either plug the head unit ISO into that (if it has ISO), or you buy and ISO adapter harness that you wire in. Bit of stuffing around, but once you have ISO its easy to change things in future.
    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
×
×
  • Create New...