Jump to content
SAU Community

Recommended Posts

I can't quite remember where I saw the photo but I do remember seeing rb26 covers painted in wrinkle paint. Very similar purple & it looked hot!

How do you find those clamps on the justjap intercooler silicon joints?

  • 2 weeks later...

I have a few ideas but at the moment I've got traction issues and with an extra 25kw it's just going to be worse, so at the moment my main focus is going to be improving that.

I have a few ideas but at the moment I've got traction issues and with an extra 25kw it's just going to be worse, so at the moment my main focus is going to be improving that.

I did the bolt into back of transfer case mod to my 32 cause the 4WD drive was near none existent, the difference is unbelievable, no more tail happy fun times :/

The lsd in my car doesn't work at all and the attesa pump has to keep priming even while standing still. So I'm going to replace a few of the consumables in the awd system which should fix most of the issues

Lol nice, I might have a chat them instead of buying a new center just hope they can do something not quite as aggressive as that tho

I check the actuator system every so often for air and nothing comes out so I think I'm pretty safe there

I have recently changed how I bleed the 4WD to cause the way the manual says to do it doesn't get all the air out :(

I got Award to rebuild a spare 32 diff I had which is now in the 34 and it is now almost like a locker lol

I can confirm. Once warm it was carrying on like my Nismo 1.5 way.

I have recently changed how I bleed the 4WD to cause the way the manual says to do it doesn't get all the air out :(

I got Award to rebuild a spare 32 diff I had which is now in the 34 and it is now almost like a locker lol

What's your new bleeding method mick?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...