Jump to content
SAU Community

Recommended Posts

Ok a bit off topic but might be relevant to the January track day too ... I'm heading to Sandown this coming Sunday and the current forecast is 35, ouch.

Any specific prep I should look at doing for such a hot day? I've got Defis for oil and water temps so will be watching those closely.

Does anyone know how R888's go in the hot (standard GG compound)?

Also would i be able to wear a dirtbike helmet for this? or will i need another type of helmet

If I were you I would get a different type, scrutineers can be a little strange with them.

Ok a bit off topic but might be relevant to the January track day too ... I'm heading to Sandown this coming Sunday and the current forecast is 35, ouch.

Any specific prep I should look at doing for such a hot day? I've got Defis for oil and water temps so will be watching those closely.

Does anyone know how R888's go in the hot (standard GG compound)?

Check your brakes are in good condition and you've got good brake fluid too.

Do the licenses you can buy on the day allow you to enter the Timed sessions or just the non-timed? Just asking as the come and try licences in the Supp Regs are a different level to the normal Level 2S ones we have...

DRIVER ELIGIBILITY
All drivers must hold a current CAMS Level 2S licence or higher and be a financial member of a Club affiliated with CAMS in Victoria.
Come and Try Level 1 Licences will be available to eligible participants, see CAMS website for further information

Do the licenses you can buy on the day allow you to enter the Timed sessions or just the non-timed? Just asking as the come and try licences in the Supp Regs are a different level to the normal Level 2S ones we have...

DRIVER ELIGIBILITY
All drivers must hold a current CAMS Level 2S licence or higher and be a financial member of a Club affiliated with CAMS in Victoria.
Come and Try Level 1 Licences will be available to eligible participants, see CAMS website for further information

It's at the discretion of the Clerk. However we will be grouping Level 1 license holders in the social group(s) with no timing.

It will be a discussion if a level 1 license holder would like to go up into a timed group.

Good question Brett,

I will check and get someone to reply.

It's at the discretion of the Clerk. However we will be grouping Level 1 license holders in the social group(s) with no timing.

It will be a discussion if a level 1 license holder would like to go up into a timed group.

Thanks Collins / Richo,

Was thinking they would be separated at the start of the day so I can let people know and that there may be a possibility of getting into the timed groups at the discretion of the clerk...

Thanks Collins / Richo,

Was thinking they would be separated at the start of the day so I can let people know and that there may be a possibility of getting into the timed groups at the discretion of the clerk...

Badically, if head screwed on. They'll have a chance of getting into the timed groups.

Ok a bit off topic but might be relevant to the January track day too ... I'm heading to Sandown this coming Sunday and the current forecast is 35, ouch.

Any specific prep I should look at doing for such a hot day? I've got Defis for oil and water temps so will be watching those closely.

Does anyone know how R888's go in the hot (standard GG compound)?

If you don't have an oil cooler, you're gonna have a very bad time. Once you see oil temp hit 120 back off as it's gonna climb top 130-135 before it starts to come back down.

R888 will be fine, you'll run outta oil (and/or brakes depending on setup) before the tyres will give out

  • Like 2

And EVO is booked into Import Monster's new service factory with a loooong ass list of shit to do.

I should be a starter for Jan 30 now, need to lock in a tune somewhere in Jan however.

If you don't have an oil cooler, you're gonna have a very bad time. Once you see oil temp hit 120 back off as it's gonna climb top 130-135 before it starts to come back down.

R888 will be fine, you'll run outta oil (and/or brakes depending on setup) before the tyres will give out

Cheers. I was trying to get the cooler sorted this week but ran out of time, aiming for early Jan hopefully. Fingers crossed I don't cook it on Sunday.

Badically, if head screwed on. They'll have a chance of getting into the timed groups.

i like that plan as you would definitely want them to know what they are doing before putting them on the track with the guys trying to cut good lap times... :D

And EVO is booked into Import Monster's new service factory with a loooong ass list of shit to do.

I should be a starter for Jan 30 now, need to lock in a tune somewhere in Jan however.

Then prepare your ears for tyre squeal and bulk understeer, or has it still got the oem suspension package?




  • Similar Content

  • Latest Posts

    • Ok thanks..that was my second question if i can somehow bypass this even with Nistune(that is all i have right now...aparat from stock ECU. So with some aftemarket it can by "bypassed" or make it work?  I know there is Link or Haltech (mainly used). We have ECUmaster here so i will gather some info about it.
    • Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
    • Ok so ABS/TCS is "not" the problem. Yeah i know now about the ABS with Nistune(i told that to the Nistune guy) but iam not 100% why or why i dont have ABS. ABS cube is in the engine (always has been) but i had braked couple of times rly hard and brakes just locked and scream. Does all Skylines have ABS cube? That boost sensor https://www.sau.com.au/forums/topic/367633-wtb-r34-gtt-turbo-pressure-sensor-pics-inside/ Is this it? I need to ask but i have a picture of engine bay and i do not see that (100% is not in that place) If i do not have this the car can do what mine is?(cutting around 4000 rpm) Here is the pic of my engine bay(only one i have) BUT i think i dont have that cuz loom was used from my RB20DE NEO and i know (obviously) that it does not have boost control or any wire to that...) so maybe that is the problem? (i dont know for 100% if that car where the engine is from had that)...but i dont have the loom from that
×
×
  • Create New...