Jump to content
SAU Community

Recommended Posts

Short story:

How Do Vented Gas Caps Work?
By Steve Smith
eHow Contributor
Save
6 Shares & Saves
Vented Gas Cap Function
  • The vented gas cap is designed to vent small amounts of air into the car gas tank line. The vented gas cap has a one-way release valve that is pressure-activated. When the pressure reaches a certain point (defined by so many pounds per square inch) the valve opens by a very small amount, relieving some of the pressure. In this case, the pressure is formed on the outside of the tank, due to the vacuum formed from the displacement of fuel on the inside. After the pressure inside the line equalizes, the pressure valve closes. The valve is set to balance the pressure with the surrounding atmosphere. Air is allowed in, but no fumes are allowed out of the gas cap, because of environmental concerns.

Inner Parts
  • The vented gas cap has a chamber under the plastic cap handle that inserts into the fuel fill line. The cap screws shut, and this chamber fits relatively close inside the intake tube of the fuel line running to the tank. On each side of the chamber are small openings where air is able to enter. These chambers lead to the pressure valve, which, as the level in the tank decreases, allows air inside to remove any possibility of a vacuum forming.

How it All Works
  • Because the fuel tank is pressure-driven from a fuel pump and gas naturally expands and evaporates, a large amount of pressure can build up inside the fuel system over time. This second kind of pressure is taken care of through the operation of the fuel pump mechanism, as the vented gas cap needs to be the one-way flap to keep evaporated gas fumes in.

All that I know from personal experience is that they are only supposed to vent one way and that it is important that they vent correctly.

  • I had one in a Subaru stop venting and the steel fuel tank started to collapse because of the level of vacuum being created.
  • In our R33 track car the cap started venting both ways which resulted in fuel covering the rear of the car - not a great look when you have the usual flames from the exhaust

thanks gents that is exactly the part I was trying to get to. funnily enough it struck me that the workshop manual might have some information, and voila!

fuel-cap.jpg

so yes, the GTR cap has a one way pressure sensitive valve that allows air in to replace the used fuel (but not out, of course)

the other half of the breathing is the "fuel overflow prevention system with check valve" which breathes excess pressure into the charcoal canister when the engine runs.

the motorsport question of course is what is needed to safely vent the tank, I don't want to sit on a fuel bomb. Pretty much every aftermarket vent is an anti roll over valve which is open at all other times, ie it allows air/fuel vapour in or out unless the car is exactly upside down.

ideally I would keep the stock cap and have a 1 way valve to allow fuel vapour to vent to atmo (via a small filter) but I am having trouble finding something good. most setups are small valves near the top of the tank that are almost guaranteed to leak fuel from a full tank in high G corners. In fact the most common valve mounts on top of the tank and doesnt allow for any venting hose at all

Some people combat that by having looped breather hose but as soon as you get liquid fuel into that hose it can no longer work as a vent which defeats the whole purpose. kind of like a S bend with the same result that gas cannot pass.

happy to hear any suggestions about a good way to deal with the venting

We had a failed breather on our EVO at the Winton 300. Caused the fuel bladder to expand, pushed the carbon bucket down onto the drive shaft - and wore a hole through the middle of it.

Thankfully we didn't a) blow up (it's right next to the exhaust) or even b) run out of fuel at the end.

I'm still not 100% sure how either of those didn't happen however.

So with the new fuel bladder we now have 4 breathers rather than 1.

post-5136-0-68034800-1455765554_thumb.jpg

lucky outcome really....

I was not happy with the design of some of those breathers they are very basic. Have you got a pic of how the 4 breathers are mounted and vented? Are you using a 90L FIA with siamese fittings?

I actually haven't seen it and it was fitted before I got the chance sorry..

It was your new mate Dylan Thomas who did the 4 vent design. He had previously suffered the same thing we had with the base Ralliart design so they did a 4 breather design. I actually just purchased Dylan's old tank as they were going from the saddle design to a boot mounted flat design as he was being team serious and wanting to extract every last litre out of his tank for 6hr .

I personally am not a fan of the safety aspects of a boot mounted tank though but that's a different topic to this one.

But Dylan would be a good bloke to chat to about fuel tank breathers.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...