Jump to content
SAU Community

Recommended Posts

8 hours ago, usmair said:

Can only work with what we've got.......

Umair , it was great to get your info, what I meant , if it had been the 6266 it would have made the 8374 low end response look even better , but I think the top end would be pretty close with both turbos

Umair,

I took the liberty of converting your results to excel and graphing them vs my pumpgas results (including corresponding boost curves). Looks like my combo of stock-bore 79mm stroker (2.75L) and/or the .92 IWG housing turbo is making a bit more bottom end than yours (below 4500 rpms), but obviously with higher boost and E85 you're crushing me anywhere over that. The boost is x10 for scaling purposes (ie 100 = 10 psi, 200 = 20 psi, etc). I'm willing to bet when converted to E85 and when I start pouring on the boost that I will make more power lower in the rpms, but not significantly so (maybe 250-300 rpms sooner), and with the increased backpressure of the .92 housing I'd bet I'll start dropping sooner as well.

Good looking dyno! :1311_thumbsup_tone2:

 

Dyno comparison to Umair.JPG

  • Like 2
Not really surprised there though. Bigger engine making more grunt down low.

How long till you put it on E85, Harris? 

Station is targeting completion in november. I'm hoping to have fuel pumps, 3.5" exhaust, and mega huge injectors done by then. I'm still on stock fmic so we will see what it can flow!

will need 100m cooler. the stockies have been known to hold power back over 400kw.

3.5" will do the job. Mine is 3.5". 4" only if you know you are going to aim for even bigger power in the future.

My injectors are 2000cc. I was told that even 1600cc on e85 wont cut the mustard for 500kw. Makes it a little harder to fine tune but its not noticeable in day to day drive.

thanks for mapping the dynos. interesting stuff!

  • Like 1

If anyone is interested, I'm maybe going to the SAU cruise to the Gosford car museum on Sunday.

Happy to take anyone for a spin so they can feel the setup for themselves.

Edited by usmair
if you need pricing on Plazmaman coolers @usmair give me a holla [emoji4]


What about me? Sounds like he's got a cooler.

I'm almost tapped on money these days (oilfield sucks here lately). I need a sponsor!
43 minutes ago, HarrisRacing said:


What about me? Sounds like he's got a cooler.

I'm almost tapped on money these days (oilfield sucks here lately). I need a sponsor!

haha but you're in the US.. shipping won't be cheap.. however happy to help out - flick me a PM on which size cooler your after, and if polished/black/raw etc..

What range of mph would you expect to get from 500kw 

 

138-140mph??

I would hope! Thats a ton of power. I ran 120 mph on 464 whp and you've got way more midrange.

On 9/3/2016 at 11:53 PM, Piggaz said:

Borg Warner EFR Series Turbo's V 2.0

 

Link to the first attempt. A wealth of knowledge in it. 

annnnd go!

We gonna be factual on this or its gonna b like the last one >_<

What wasn't factual in there? 

You must have some EFR experience to share with us if you know there was nothing factual in there? 

 

 

Edited by Mick_o
  • Like 2
On 9/10/2016 at 10:00 PM, Mick_o said:

What wasn't factual in there? 

You must have some EFR experience to share with us if you know there was nothing factual in there? 

 

 

at the end of the thread which got it locked . 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
    • If it (the code) wasn't still current, it should have gone away by itself by now. No, nothing it 10/10. But it is quite likely. Everything else to do with the ignition could still be responsible (which is wires and connectors). The car is an old piece of shit now, so all the wires and connectors are also old pieces of shit.
    • Lock me in mate, although I'm not sure if I'll be heading up from Goulburn or down from Sydney, either way, return will be back to Goulburn 
×
×
  • Create New...