Jump to content
SAU Community

Recommended Posts

8 hours ago, usmair said:

Can only work with what we've got.......

Umair , it was great to get your info, what I meant , if it had been the 6266 it would have made the 8374 low end response look even better , but I think the top end would be pretty close with both turbos

Umair,

I took the liberty of converting your results to excel and graphing them vs my pumpgas results (including corresponding boost curves). Looks like my combo of stock-bore 79mm stroker (2.75L) and/or the .92 IWG housing turbo is making a bit more bottom end than yours (below 4500 rpms), but obviously with higher boost and E85 you're crushing me anywhere over that. The boost is x10 for scaling purposes (ie 100 = 10 psi, 200 = 20 psi, etc). I'm willing to bet when converted to E85 and when I start pouring on the boost that I will make more power lower in the rpms, but not significantly so (maybe 250-300 rpms sooner), and with the increased backpressure of the .92 housing I'd bet I'll start dropping sooner as well.

Good looking dyno! :1311_thumbsup_tone2:

 

Dyno comparison to Umair.JPG

  • Like 2
Not really surprised there though. Bigger engine making more grunt down low.

How long till you put it on E85, Harris? 

Station is targeting completion in november. I'm hoping to have fuel pumps, 3.5" exhaust, and mega huge injectors done by then. I'm still on stock fmic so we will see what it can flow!

will need 100m cooler. the stockies have been known to hold power back over 400kw.

3.5" will do the job. Mine is 3.5". 4" only if you know you are going to aim for even bigger power in the future.

My injectors are 2000cc. I was told that even 1600cc on e85 wont cut the mustard for 500kw. Makes it a little harder to fine tune but its not noticeable in day to day drive.

thanks for mapping the dynos. interesting stuff!

  • Like 1

If anyone is interested, I'm maybe going to the SAU cruise to the Gosford car museum on Sunday.

Happy to take anyone for a spin so they can feel the setup for themselves.

Edited by usmair
if you need pricing on Plazmaman coolers @usmair give me a holla [emoji4]


What about me? Sounds like he's got a cooler.

I'm almost tapped on money these days (oilfield sucks here lately). I need a sponsor!
43 minutes ago, HarrisRacing said:


What about me? Sounds like he's got a cooler.

I'm almost tapped on money these days (oilfield sucks here lately). I need a sponsor!

haha but you're in the US.. shipping won't be cheap.. however happy to help out - flick me a PM on which size cooler your after, and if polished/black/raw etc..

What range of mph would you expect to get from 500kw 

 

138-140mph??

I would hope! Thats a ton of power. I ran 120 mph on 464 whp and you've got way more midrange.

On 9/3/2016 at 11:53 PM, Piggaz said:

Borg Warner EFR Series Turbo's V 2.0

 

Link to the first attempt. A wealth of knowledge in it. 

annnnd go!

We gonna be factual on this or its gonna b like the last one >_<

What wasn't factual in there? 

You must have some EFR experience to share with us if you know there was nothing factual in there? 

 

 

Edited by Mick_o
  • Like 2
On 9/10/2016 at 10:00 PM, Mick_o said:

What wasn't factual in there? 

You must have some EFR experience to share with us if you know there was nothing factual in there? 

 

 

at the end of the thread which got it locked . 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...