Jump to content
SAU Community

Recommended Posts

4 hours ago, Piggaz said:

Do you plan on building this soon? How hard do you rev it? Any other changes apart from the snail? 

Its gonna be interesting to see the difference, especially in the real world.

Still on the factory gearbox?

Will build when it pops.  Probably rev to 8500.

It has getrag behind it now with diff. No other changes to motor aside from turbo. 

37 minutes ago, usmair said:

Will build when it pops.  Probably rev to 8500.

It has getrag behind it now with diff. No other changes to motor aside from turbo. 

Do you at least have decent headstuds? the OEM ones are known to stretch and lift heads

3 hours ago, Dose Pipe Sutututu said:

Do you at least have decent headstuds? the OEM ones are known to stretch and lift heads

yes. head gasket, studs, springs, valves etc etc have been upgraded. Basic stuff is done

Edited by usmair
  • Like 1
On 05/02/2018 at 8:31 PM, usmair said:

I ended up with 1.05 as it didnt look like the 1.45 would fit on current mani.

Should be on this week with tune next week or so.

Nice, I don't really think the 1.05 should be a show stopper at all - especially on a "mild" 2.6, I'd say the turbine speed would be the key thing to keep an eye on.  Very interested to see what the difference is from the 1.05 EFR8374!

 

Good luck :)

After reading through this thread you all convinced me to not get a Garrett GTX3582R and instead I just purchased purchased a efr8374 1.05 ex gate from gcg turbos yesterday. Also brought a 6boost split pulse manifold and 50mm turbosmart pro gate.

Can’t wait to institute in the coming weeks.

  • Like 2

Guys, what do you think the below setup? Would it be laggy?

1. efr9180 1.05

2. Fullrace manifold running twin gates

3. Rb26 87mm forged CP piston 9:1 compression with tomei rods

4. Ported head with tomei type b cams

5. Greddy intake

6. Getrag with 4.1 final drives

I hv been searching for results of 9180 on stock 2.6l displacement but couldnt find much info.  what i am really after is whether it is going to be laggy.

Fuel will be 97 but running on wmi.

Thanks

 

 

From guys that have gone from -5’s/2530’s to a 9180/1.05, it behaves like a pair of -5’s to 4000 rpm then the 9180 will walk away from it.

If an 8374/1.05 is on 500 rpm earlier than a pair of -5’s then how much later can a 9180 be?

*using -5’s as a yard stick.

How hard will you be leaning on it?

It won’t be the most responsive setup in the world but you are talking about a 94 lb/minute turbo all in.

1 hour ago, gzro said:

Guys, what do you think the below setup? Would it be laggy?

1. efr9180 1.05

2. Fullrace manifold running twin gates

3. Rb26 87mm forged CP piston 9:1 compression with tomei rods

4. Ported head with tomei type b cams

5. Greddy intake

6. Getrag with 4.1 final drives

I hv been searching for results of 9180 on stock 2.6l displacement but couldnt find much info.  what i am really after is whether it is going to be laggy.

Fuel will be 97 but running on wmi.

Thanks

 

 

30psi by 5000rpmish. Will have actual results next week

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • i will be there 😁
    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Yeah mate, never miss it.
×
×
  • Create New...