Jump to content
SAU Community

Recommended Posts

3 hours ago, Dose Pipe Sutututu said:

I am back from 1 month of no SAU and car shit

Adaptronic is coming out, and is now for sales. $800 for SAU members $850 for Facebook or Scumtree or eScum

Ahh how good is it to have a month off.... (congrats by the way kent!!)

Why the move to a Halaltech?

2 hours ago, dr phil said:

Not going an Adaptronic modular, or an EMU Black?

As much as I support and recommend Adaptronic, a Haltech is so much faster to tune and get going when compared to an Adaptronic. The ECU Master range does look promising but never used it before, so means will need to spend time to acquaint myself with it. 

2 hours ago, timmy_89 said:

Ahh how good is it to have a month off.... (congrats by the way kent!!)

Why the move to a Halaltech?

Haha thanks man, part of the club now :)

I've outgrown the 440D Select and also over the idiosyncrasies involved with their software. Every time I set up the crank prime value it reverts back to a negative value approximately 4 to 6 starts, so these days I end up carrying the laptop with me to start the car lol.

Over night parts from Kudos Motorsports.

OEM wheel bearings all round, road safe ball joints all round and new washer motors because I like a clean windscreen lol.

34464030_240876389797466_2688695212863127552_n.thumb.jpg.d7357ee9411336a3571b50675b85ff73.jpg

 

So.... Had a few beers at work and accidentally ordered a few things.

AI SPR400, 1x DW200 lift pump, 1x more Wallahbro 460..

Hopefully no more fuelling issues ?

 

2 hours ago, Dose Pipe Sutututu said:

Do youse English? 

Wallah DW200 is lift, twin 460s feed!

Mashallah 

Who was english?

Did you order a stroker or you didnt hvae that many beers?

23 minutes ago, WantGTR said:

 

Who was english?

Did you order a stroker or you didnt hvae that many beers?

I'm not that dumb brah :)

Watch my little 2.5L motor thrash 2.6L fags with twins 

  • Like 2
So.... Had a few beers at work and accidentally ordered a few things.
AI SPR400, 1x DW200 lift pump, 1x more Wallahbro 460..
Hopefully no more fuelling issues [emoji28]
It is good to know that others do this. My Mrs is trying to convince me that late night / early morning orders from Plazmaman, rhd, amayama, etc. are a bad idea

Some parts to help my motor spin backwards and forget tunes ? 

Special shout out to Alanah and James at Game On Motorsports. Twisted my arm and ended up with an Elite 2500 and a 4 bar MAP sensor instead of me only just getting an Elite 2000 and using the onboard 3 bar MAP sensor lol.

20180616_133343.thumb.jpg.94a34d012a86a6fc67cf98ef91f98856.jpg

Currently car is at thr mechanic getting new wheel bearings and ball joints installed because I cbf doing it myself (although I have all the tools and access to my mate's press)

  • Like 3
26 minutes ago, hy_rpm said:

Planning on running more than 3bar boost?

Glad someone did the maths. I was going to get to it tomorrow if I had time.

  • Like 1
3 hours ago, hy_rpm said:

Planning on running more than 3bar boost?

You mean 2 bar of positive pressure, 3bar sensor needs to also read vacuum too :)

Also if you don't use the onboard MAP sensor you can use that to adjust the tune for atmospheric pressure changes 

Lastly I prefer the MAP sensor as close to the plenum as possible.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Hi. This is just my curiosity because iam sure the tuner figure something out...but either way i want to ask. The "problem" is that the Nistune ECU (Stagea FW and RB25DET NEO from Stagea) sees many times the speed than the speedo does(he says the speedo show 120 km/h - correct speed and the ECU shows like 510km/h ) I told him that this car/tranny getting speed from rear diff. If iam not mistaken the RB25DET NEO "need" to see tranny speed sensor? (my tranny has the plug for it). So couple of "question" If he connects/wire the speed sensor to the tranny...are the signals gonna intervene and if...what if he disconnects the rear diff one and the speedo stops working? Or the "new" sensor from the tranny "take over" and will not going need the one from diff? As i said i know he figure/get that done...iam just curious to know what are the solutions 🙂 
    • Your IACV is set to idle too low. You need to adjust it via the screw Duncan mentioned. From memory it should be 650rpm with the valve electrics unplugged. What is it trying to idle at with the IACV plugged in?
    • Ahhh, I need the whole head unit. I definitely needed to roll back through and review your setup, ha ha! Neat setup they have going on. I just need a full double din head unit. But I want good and responsive. I might have to review what the likes of pioneer have out these days.
    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
×
×
  • Create New...